United States |
Office of Research and |
EPA/600/R-95/178 |
Environmental Protection |
Development |
April 1996 |
Agency |
Washington DC 20460 |
|
ICR Microbial Laboratory
Manual
ICR MICROBIAL LABORATORY MANUAL
by
- Shay Fout, Ph.D., Frank W. Schaefer III, Ph.D., James W. Messer, Ph.D., Daniel R. Dahling and Ronald E. Stetler
Biohazard Assessment Research Branch Human Exposure Research Division Cincinnati, Ohio 45268
NATIONAL EXPOSURE RESEARCH LABORATORY OFFICE OF RESEARCH AND DEVELOPMENT
U.S. ENVIRONMENTAL PROTECTION AGENCY CINCINNATI, OHIO 45268
NOTICE
The ICR Microbial Laboratory Manual was prepared by the authors in response to a request from the Office of Water for support in ICR implementation. The methods and laboratory approval components contained in the manual were based upon consensus agreements reached at several workshops attended by industry, academia and U.S. EPA personnel and input from the ICR Microbiology Implementation team, which consisted of U.S. EPA personnel from the Office of Research and Develop- ment, Office of Water and representatives from Regional Offices. The manual has been peer reviewed by experts outside of U.S. EPA in accordance with the policy of the Office of Research and Development. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.
ACKNOWLEDGMENTS
The contributions from Robert S. Safferman, Robert H. Bordner and John A. Winter, the helpful suggestions from members of the ICR Microbiology Implementation Team, the graphical support of Fred P. Williams Jr. and the secretarial assistance of Mary Ann Schmitz and Cordelia Nowell are greatly appreciated.
ii
SECTION VIII. VIRUS MONITORING PROTOCOL FOR THE ICR TABLE OF CONTENTS
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-3
PART 1 — SAMPLE COLLECTION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . VIII-4
APPARATUS AND MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-4
MEDIA AND REAGENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-11
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-12
PART 2 — SAMPLE PROCESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-16 QUALITY CONTROL AND PERFORMANCE EVALUATION SAMPLES . . VIII-16 QC Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-16
PE Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-16
ELUTION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-17
Apparatus and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-17
Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-17
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-18 ORGANIC FLOCCULATION CONCENTRATION PROCEDURE . . . . . . . . . VIII-19 Apparatus and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-19
Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-20
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-20
PART 3 — TOTAL CULTURABLE VIRUS ASSAY . . . . . . . . . . . . . . . . . . . . . . . . VIII-23 QUANTAL ASSAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-23
Apparatus and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-23
Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-23
Sample Inoculation and CPE Development . . . . . . . . . . . . . . . . . . . . . . . . . VIII-23 Virus Quantitation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-27 REDUCTION OF CYTOTOXICITY IN SAMPLE CONCENTRATES . . . . . . . VIII-28 Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-28
Procedure for Cytotoxicity Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-29
PART 4 — CELL CULTURE PREPARATION AND MAINTENANCE . . . . . . . . . VIII-30 PREPARATION OF CELL CULTURE MEDIUM . . . . . . . . . . . . . . . . . . . . . . . VIII-30 General Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-30
Apparatus and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-30
Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-32
Media Preparation Recipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-32 PREPARATION AND PASSAGE OF BGM CELL CULTURES . . . . . . . . . . . . VIII-35
Vessels and Media for Cell Growth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-35
General Procedure for Cell Passage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-35
VIII-1
Procedure For Performing Viable Cell Counts . . . . . . . . . . . . . . . . . . . . . . . VIII-37 PROCEDURE FOR PRESERVATION OF BGM CELL LINE . . . . . . . . . . . . . VIII-38
Preparation of Cells for Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-38
Procedure for Freezing Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-39
Procedure for Thawing Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-39
PART 5 — STERILIZATION AND DISINFECTION . . . . . . . . . . . . . . . . . . . . . . . . VIII-40 GENERAL GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-40
STERILIZATION TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-40 Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-40
Autoclavable Glassware, Plasticware, and Equipment . . . . . . . . . . . . . . . . . VIII-40 Chlorine Sterilization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-41 PROCEDURE FOR VERIFYING STERILITY OF LIQUIDS . . . . . . . . . . . . . . VIII-41 Media and Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-42
Verifying Sterility of Small Volumes of Liquids . . . . . . . . . . . . . . . . . . . . . . VIII-42 Visual Evaluation of Media for Microbial Contaminants . . . . . . . . . . . . . . . VIII-42 CONTAMINATED MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-42
PART 6 — BIBLIOGRAPHY AND SUGGESTED READING . . . . . . . . . . . . . . . . VIII-43 PART 7 — VENDORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-46
PART 8 — EXAMPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-48
EXAMPLE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-48
EXAMPLE 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-56
PART 9 — DATA SHEETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIII-63
VIII-2
FOREWORD
The surface water treatment rule (40 CFR Part 141) established the maximum contam- ination level for enteric virus in public water systems by requiring that systems using surface water or ground water under the influence of surface water reduce the amount of virus in source water by 99.99%. The rule requirements are currently met on basis of treatment alone (e.g., disinfection and/or filtration), and thus the degree of actual protection against waterborne viral disease depends upon the source water quality. Utilities using virus-free source water or source water with low virus levels may be overtreating their water, while utilities using highly contaminated water may not be providing adequate protection. To determine more adequately the level of protection from virus infection and to reduce the levels of disinfection and disinfection byproducts, where appropriate, the U.S. EPA is requiring all utilities serving a population of over 100,000 to monitor their source water for viruses monthly for a period of 18 months. Systems finding greater than one infectious enteric virus particle per liter of source water must also monitor their finished water on a monthly basis. The authority for this requirement is Section 1445(a)(1) of the Safe Drinking Water Act, as amended in 1986.
This Virus Monitoring Protocol was developed by virologists at the U.S. EPA and modified to reflect consensus agreements from the scientific community and comments to the draft rule. The procedures contained herein do not preclude the use of additional tests for research purposes (e.g., polymerase chain reaction-based detection methods for non-cytopathic viruses).
The concentrated water samples to be monitored may contain pathogenic human enteric viruses. Laboratories performing virus analyses are responsible for establishing an adequate safety plan and must rigorously follow the guidelines on sterilization and aseptic techniques given in Part 5.
Analytical Reagent or ACS grade chemicals (unless specified otherwise) and deionized or distilled reagent grade water (dH2O; see Table IV-1) should be used to prepare all media and reagents. The dH2O must have a resistance of greater than 0.5 megohms-cm at 25 C, but water with a resistance of 18 megohms-cm is preferred. Water and other reagent solutions may be available commercially. For any given section of this protocol only apparatus, materials, media and reagents that are not described in previous sections are listed, except where deemed necessary. The amount of media prepared for each Part of the Protocol may be increased proportionally to the number of samples to be analyzed.
VIII-3
PART 1 — SAMPLE COLLECTION PROCEDURE
APPARATUS AND MATERIALS
Several configurations are given below for the assembly of the filter apparatus. The standard filter apparatus will be used for all sampling, except where a prefilter, dechlorination or pH adjustment are required.
- Standard filter apparatus (see Figure VIII-1).
- Parts needed (letters in bold print represent the origin of the abbreviations used to identify parts in the figures):
- One BR — Backflow Regulator (Watts Regulator1 Product Series 8 — ¾” Hose Connection Vacuum Breaker).
- One SF — Swivel Female insert with garden hose threads (United States Plastic Product No. 63003).
- Three sections of BT — Braided Tubing, ½” clear (Cole-Parmer Product No. G- 06401-03).
- Six HC1 — Hose Clamps (Cole-Parmer Product No. G-06403-20).
- One HF1 — Hose Fitting, nylon, ” male NPT × ½” tubing ID (United States Plastic Product No. 61141).
- One PR — Pressure Regulator (Watts Regulator Product No. ” 26A (or 263A), Suffix B).
- One PN — PVC Nipple, ” male NPT (Ryan Herco Product No. 3861-057; not required with the 263A regulator).
- One TE — PVC TEE with ” female NPT ports (Ryan Herco Product No. 3805-003; not required with the 263A regulator).
- One RB1 — Reducing Bushing, ” NPT(M) × ¼” NPT(F) (Cole-Parmer Product No. G-06349-32; not required with the 263A regulator).
1See Part 7 for addresses of the vendors listed. The vendors listed in this protocol represent one possible source for required products. Other vendors may supply the same or equivalent products.
VIII-4
Figure VIII-1.
Standard Filter Apparatus
- One PG — Pressure Gauge 0-30 pound per square inch (PSI; Cole-Parmer Product No. G-68004-03; place in ¼” gauge port if using the 263A regulator).
- One RA — Reducing Adaptor, ½” female NPT × ” male NPT (Cincinnati Valve and Fitting Product No. SS-8-RA-6).
- One MQ1 — Male Quick Connect, ½” male NPT (Cincinnati Valve and Fitting Product No. SS-QF8-S-8PM; appropriate hose fittings and braided tubing can be substituted for quick connects).
- Two FQ1 — Female Quick Connects, ½” female NPT (Cincinnati Valve and Fitting Product No. SS-QF8-B-8PF).
- Two RN1 — Reducing Nipples, ¾” male NPT × ½” male NPT (Cole-Parmer Product No. G-06349-35).
- One CH — Cartridge Housing with wench (Cuno Product No. AP11T).
- One FC — Filter Cartridge, positively charged 1MDS, ZetaPor Virosorb (Cuno Product No. 45144-01-1MDS).
- One MQ2 — Male Quick Connect, ½” female NPT (Cincinnati Valve and Fitting Product No. SS-QF8-S-8PF).
- One HF2 — Hose Fitting, ½” male NPT × ½”tubing ID (United States Plastic Product No. 62142).
- One WM — Water Meter (Neptune Equipment Product No. ” Trident 10). The water meter should be used in a horizontal position and protected from freezing. The order should specify that the meters be rated in gallons (1 gal = 0.1337 ft3 or 3.7854 L). If not specified, meters may be rated in cubic feet (1 ft 3
= 7.481 gal or 28.316 L).
- One HF3 — Hose Fitting, nylon, ¾” male NPT × ½” tubing ID (United States Plastic Product No. 61143).
- One FV — Flow Control Valve (Plast-O-Matic Valves Product No. FC075B-3- PVC).
VIII-6
- Apparatus assembly — the standard filter apparatus consists of three modules: the regulator module, the cartridge housing module and the discharge module.
Teflon tape (Cole-Parmer Product No. G-08782-27) must be used on all threaded, non-compression fittings. It is recommended that apparatus assembly be performed by the analytical laboratory contracted by the utility to analyze ICR samples for viruses).
- Regulator module — in order, as shown in Figure VIII-1, connect the backflow regulator (BR) to a swivel female insert (SF). Clamp a piece of braided tubing (BT) onto the tubing connector of the swivel female insert using a hose clamp (HC1). Clamp the other end of the tubing to a × ½” hose fitting (HF1). Screw the fitting into the inlet of the pressure regulator (PR). Connect the outlet of the pressure regulator to the PVC TEE (TE) via a PVC nipple (PN). Connect the pressure gauge (PG) to the top of the PVC TEE using the reducing bushing (RB). Attach a reducing adaptor (RA) to the remaining connection on the PVC TEE. Add a male quick connect (MQ1) to the reducing adaptor.
- Cartridge housing module — Attach a female quick connect (FQ1) to a reducing nipple (RN1). Connect the reducing nipple to the inlet of the cartridge housing (CH). Attach another reducing nipple to the outlet of the housing. Attach a male quick connect (MQ2) to the reducing adaptor.
- Discharge module — attach a female quick connect (FQ1) to a hose fitting (HF2). Connect a piece of braided tubing to the hose fitting with a hose clamp (HC1). Clamp the other end of the braided tubing to a swivel female insert with another hose clamp. Attach a swivel female insert to the inlet of the water meter (WM). Attach another swivel female insert to the outlet of the meter and connect a piece of braided tubing with a hose clamp. Clamp the other end of the tubing to a hose fitting (HF3) with a hose clamp. Screw the fitting into the inlet of the flow control valve (FV). An additional hose fitting (not shown) may be added to the flow control valve for the attachment of a sufficient length of tubing to reach a drain. The discharge module does not have to be sterilized.
- Connect the cartridge housing module to the regulator module at the quick connect. The combined regulator and cartridge housing modules should be sterilized with chlorine as described in Part 5. Presterilize a 1MDS filter cartridge (FC) as described in Part 5 and place it into the cartridge housing using aseptic technique. Replace the housing head of the cartridge housing and tighten with a cartridge housing wench. Check to ensure that the filter is adequately sealed by shaking the housing. Adequately sealed filters should not move. For convenience during shipping, the regulator and cartridge housing modules may be separated. Seal all openings into the modules with sterile aluminum foil.
VIII-7
- Prefilter module for waters exceeding 75 nephelometric turbidity units (NTU) and for any other conditions that prevent the minimum sampling volumes from being obtained (see Figure VIII-2).
- Additional parts needed: One PC — 10 µm Polypropylene Prefilter Cartridge (Parker Hannifin Product No. M19R10-A); in addition, a female quick connect (FQ1), two reducing nipples (RN1), a cartridge housing (CH) and a male quick connect (MQ2) as described for the standard apparatus are needed.
- Module assembly — in order, as shown for the prefilter module in Figure VIII-2, attach a female quick connect (FQ1) to a reducing nipple (RN1). Connect the reducing nipple to the inlet of the cartridge housing (CH). Attach another reducing nipple to the outlet of the housing. Attach a male quick connect (MQ2) to the reducing adaptor. Sterilize the unit with chlorine as described in Part 5 and add a presterilized polypropy- lene prefilter cartridge using aseptic technique. Cover the ends with sterile aluminum foil. The prefilter module may be sent to the utility and stored in a clean location until needed.
- Injector modules for source or finished water requiring pH reduction and for finished waters requiring dechlorination (see Figure VIII-2).
- Additional parts needed:
- Two FQ2 — Female Quick Connects, ½” male NPT (Cincinnati Valve and Fitting Product No. SS-QF8-B-8PM).
- Four ME — Male Elbows, ” male NPT (Cincinnati Valve and Fitting Product No. SS-6-ME).
- Two RN2 — Reducing Nipples, ” male NPT × ½” male NPT (Cole-Parmer Product No. G-6349-85).
- Two RB2 — Reducing Bushings, ” female NPT × ½” male NPT (Cole- Parmer Product No. G-06349-34).
- Three IN — In-line INjectors (DEMA Engineering Product No. 203B ” female NPT; a metering pump and appropriate connectors may be substituted for an injector).
- Three HC2 — Hose Clamps (Cole-Parmer Product No. G-06403-10).
VIII-8
Figure VIII-2. Additional Modules for the Standard Filter Apparatus
- In addition, four reducing adaptors (RA), four PVC TEEs (TE), two PVC nipples (PN), two reducing bushings (RB1), two pressure gauges (PG), two female quick connects (FQ1), two male quick connects (MQ1) and two male quick connects (MQ2) as described for the standard apparatus are needed. Two union ball joints, ” female NPT (not shown; Cincinnati Valve and Fitting Product No. SS-6-UBJ) and two PVC nipples may be used in place of the two reducing nipples (RN2), male quick connects (MQ2), female quick connects (FQ1) and reducing bushings (RB2) used with the double injector module.
- Module assembly:
- Single Injector Module — assemble the parts in order as shown for the single injector module in Figure VIII-2. Attach a female quick connect (FQ2) to a reducing adaptor (RA). Connect the adaptor to the inlet of the injector (IN). Connect the outlet of the injector to a PVC TEE (TE) via a PVC nipple (PN). Connect a pressure gauge (PG) to the top of the PVC TEE using a reducing bushing (RB1). Attach a reducing adaptor (RA) to the remaining connection on the PVC TEE. Add a male quick connect (MQ1) to the reducing adaptor.
- Double Injector Module — assemble the parts as shown for the double injector module in Figure VIII-2. Assemble the main portion by attaching a female quick connect (FQ2) to a reducing adaptor (RA). Connect the adaptor to the top connector of a PVC TEE (TE). Add a male elbow (ME) to one of the connec- tions on the PVC TEE. Attach a reducing nipple (RN2) to the other connection. If using a union ball joint in place of the quick connects, attach a PVC nipple (not shown) to the other connection. Add a male quick connect (MQ2) to the reducing nipple or add one portion of a union ball joint (not shown) to the PVC nipple. Connect the inlet side of an injector (IN) to the male elbow. Attach another male elbow to the outlet of the injector. Connect the male elbow to another PVC TEE. Connect a reducing nipple (RN2 or PVC nipple) to the other end of the second PVC TEE. Add a male quick connect (MQ2) to the reducing nipple as above (or add one portion of the second union ball joint to the PVC nipple). Connect the top connector of the second PVC TEE to a third PVC TEE via a PVC nipple (PN). Connect a pressure gauge (PG) to the top of the third PVC TEE using a reducing bushing (RB1). Attach a reducing adaptor (RA) to the remaining connection on the third PVC TEE. Add a male quick connect (MQ1) to the reducing adaptor. Attach two male elbows (ME) to the inlet and outlet of a second injector (IN). Connect two reducing bushings (RB2) or, if used, the bottom portion or the two union ball joints (not shown) to the male elbows. Connect a female quick connect (FQ1) to each reducing bushing. Orient the second injector so that the direction of flow is the same as the first injector (the arrows on the injectors should both point towards the pressure gauge side of the assembly). Connect the two female quick connects to the male
VIII-10
quick connects of the main portion to complete the assembly or, if used, connect the two portions of the union ball joints.
- Sterilize the single and double modules with chlorine as described in Part 5. Cover the ends, including the injector port, with sterile aluminum foil. Sterilize the inside and outside surfaces of the Injector Tubing (IT; injector tubing is sup- plied with each injector). Place the tubing in a sterile bag or wrapping in such a way that the ends may be removed without contaminating them. The injector modules may be shipped to the utility and stored in a clean location until needed.
- Portable pH probe (Omega Product No. PHH-1X)
- Portable temperature probe (Omega Product No. HH110).
- Commercial ice packs (Cole-Parmer Product No. L-06346-85).
- One liter polypropylene wide-mouth bottles (Nalge Product No. 2104-0032).
- Insulated shipping box with carrying strap (17″ × 17″ × 13″; Cole-Parmer Product No. L- 03748-00 and L-03742-30).
- Miscellaneous — aluminum foil, data card (see Part 9), hosecock clamp, surgical gloves, screwdriver or pliers for clamps, waterproof marker.
- Chemical resistant pump capable of supplying 30 PSI at 3 gal/min and appropriate connectors (for use where garden hose-type pressurized taps for the source or finished water to be monitored are unavailable and for QC samples). Follow the manufacturer’s recommenda- tions for pump priming.
MEDIA AND REAGENTS
- 2% sodium thiosulfate (Na2S2O3) — dissolve 100 g of Na2S2O3 in a total of 5000 mL dH2O to prepare a stock solution. Autoclave for 30 min at 121 C.
- Hydrochloric acid (HCl) — Prepare 0.1, 1 and 5 M solutions by mixing 50, 100 or 50 mL of concentrated HCl with 4950, 900 or 50 mL of dH2O, respectively. Prepare solutions to be used for adjusting the pH of water samples at least 24 h before use.
VIII-11
PROCEDURE
Operators must wear surgical gloves and avoid conditions that can contaminate a sample with virus. Gloves should be changed after touching human skin or handling compo- nents that may be contaminated (e.g., water taps, other environmental surfaces).
Step 1. Purge the water tap to be sampled before connecting the filter apparatus. Continue the purging for 3-3 min or until any debris that has settled in the tap line has cleared. Then turn off the water tap.
Source water sampling must be conducted at the plant intake, before impoundment, chlorination or any other treatment. Finished water sampling must be conducted at the point of entry into the distribution system. If it is necessary to use a pump for sampling, sterilize the pump with chlorine as described in Part 5 or flush with 20 gal of water to be sampled before each use.
Step 2. Remove the foil from the backflow regulator (see Figure VIII-1) on a regulator module. Loosen the swivel female insert slightly to allow it to turn freely and connect the backflow regulator to the tap. Retighten the swivel female insert. Disconnect the cartridge housing module at the quick connect following the pressure gauge (the insertion point shown in Figure VIII-1), if connected, and cover the open ends leading into the modules with sterile foil.
Step 3. Remove the foil from the ends of the discharge module and from the free end of the regulator module. Connect the discharge module to the regulator module. Place the control flow valve or tubing connected to the outlet of the flow control valve into a one liter plastic bottle. Note that the injector module, the prefilter module and the cartridge housing module must not be attached to the apparatus at this stage of the procedure!
Step 4. Slowly turn on the tap and adjust the pressure regulator until the pressure gauge on the regulator module reads 30 PSI. If the tap is incapable of 30 PSI, adjust the regulator to achieve the maximum pressure. Pressures less than 30 PSI will result in a reduced flow rate and thus longer sampling times. Flush the apparatus assembly with at least 20 gal of the water to be sampled. While the system is being flushed, measure the pH, the temperature and the turbidity on the water collecting in and overflowing from the one liter plastic bottle. Record the values onto the Sample Data Sheet (see Part 9).
The pH meter should be calibrated before each use for the pH range of the water to be sampled.
The turbidity reading may be taken from an in-line turbidimeter connected to the tap being used.
Step 5. If the sample has a pH above 8.0 or contains a disinfectant, turn off the water at the tap and disconnect the discharge module from the regulator module. Remove the foil from the
VIII-12
ends of a single injector module (see Figure VIII-2) and connect the module to the male quick connect of the regulator module. Reattach the discharge module.
Step 6. If the sample has a pH above 8.0 and contains a disinfectant, turn off the water at the tap and disconnect the discharge module from the regulator module. Remove the foil from the ends of a double injector module (see Figure VIII-2) and connect the module to the male quick connect of the regulator module. Reattach the discharge module.
Step 7. If an injector module has been added, remove the foil from the injector port(s) and attach the injector tubing to each port. Add a hosecock clamp to each injector tubing and tighten completely to prevent flow into the injector(s). Turn the fine metering adjustment screw on each injector (the smaller screw) clockwise as far as it will go to minimize the flow rate until the injectors are adjusted (note that the injectors were designed to have a minimum flow rate of 20-30 mL/min; thus completely closing the fine metering adjustment screw does not stop the flow). Place the other end of each tubing into the appropriate sterile graduated container containing 0.1 M HCl or 2% thiosulfate. Take care not to touch or contaminate the surfaces of the injector tubing that will be placed in the graduated containers. Slowly turn on the tap again and readjust the pressure regulator, if necessary.
Step 8. If a single injector module has been added, continue to flush the apparatus and adjust the water bypass screw on the injector (the larger adjustment screw) until the pressure gauge on the injector module is about 35% less than the pressure gauge on the regulator module (e.g., 19 PSI when the gauge on the regulator module reads 30 PSI; a minimum of a 35% pressure drop is required to achieve suction). Loosen the hosecock clamp and observe whether suction is occurring. If not, slowly increase the pressure drop until suction starts.
- If the pH value of the water sample is greater than 8.0, ensure that the injector tubing is placed into a graduated container containing 0.1 M HCl. While continuing to measure the pH in the one liter plastic bottle, adjust the fine metering adjustment screw on the injector to add sufficient HCl to give a pH of 6.5 to 7.5. It may be necessary to use the hosecock clamp to reduce the flow rate to less than 20-30 mL/min or to use a more dilute or concentrated HCl solution with some water samples. When the pH stabilizes at a pH of
6.5 to 7.5, continue with Step 10. Record the adjusted pH onto the Sample Data Sheet.
- If the water to be sampled contains a disinfectant, ensure that the injector tubing is placed into a graduated container containing 2% thiosulfate. Adjust the fine metering adjustment screw on the injector to add thiosulfate at a rate of 10 mL/gal (2.6 mL/L or 30 mL/min at a flow rate of 3 gal/min; note that at this rate, approximately 3-4 L of thio- sulfate solution will be required per sample). When the proper rate is achieved, record the addition of thiosulfate on the Sample Data Sheet and continue with Step 10.
Step 9. If a double injector module is being used, continue to flush the apparatus and turn the water bypass screws on each injector clockwise as far as possible. Then turn the water
VIII-13
bypass screws on each regulator one half turn counter clockwise. Continue turning the screws evenly one half turn counter clockwise until the pressure gauge on the double injector module is 35% less than the pressure gauge on the regulator module. Ensure that the tubing from one injector is placed into a graduated container containing 0.1 M HCl and the other into a graduated container containing 2% sodium thiosulfate. Loosen the hosecock clamps. Since there may be slight differences between the injectors and since the pressure reading after the injectors reflects an average pressure drop from both injectors, some additional adjustment of the water bypass screws may be required to obtain suction on each injector. After confirming that each injector is drawing fluid, adjust the flow of HCl and thiosulfate as in Step 8a-8b above. Record the final pH and the addition of thiosulfate on the Sample Data Sheet and continue with Step 10.
Step 10. After adjusting the injectors, if required, and flushing the system with at least 20 gal, turn off the flow of water at the sample tap and remove the discharge module. If the water sample has a turbidity greater than 75 NTU, remove the foil from each end of the prefilter module and connect the prefilter module (see Figure VIII-2) to the end of the regulator module or to the end of one of the injector modules, if used. Remove the foil from the cartridge housing module and connect it to the end of the regulator module, or to the end of the injector module or the prefilter module, if used. Connect the discharge module to the cartridge housing module.
Step 11. Record the sample number, location, date, time of day and initial gallon (or cubic feet) reading from the water meter onto the Sample Data Sheet.
Use the unique utility-specific sample numbers assigned by the ICR Joint Application Design database.
Step 12. Slowly turn on the water with the filter housing placed in an upright position, while pushing the red vent button on top of the filter housing to expel air. When the air is totally expelled from the housing, release the button, and open the sample tap completely. Readjust to 30 PSI, if necessary. Check the thiosulfate usage rate or the pH of the discharged water if an injector(s) is being used and readjust, if necessary.
Step 13. Sample a minimum volume for source water of 200 L (7.1 ft3, 52.8 gal) and for finished water of 1500 L (53.0 ft3, 396.3 gal). Samples for source and finished waters must not exceed 300 L (10.6 ft3, 79.3 gal) and 1800 L (63.6 ft3, 475.5 gal), respectively. For source water the total amount of sample that can be passed through a filter will depend upon water quality, however, it should be possible to obtain the minimum volume using the procedures described above.
Samples should be monitored periodically during the sampling. If the filter clogs, contact the approved analyst for further instructions. Since the flow rate may change during sampling due to filter clogging, thiosulfate addition and the adjusted pH of the sample must be checked regularly.
VIII-14
Step 14. Turn off the flow of water at the sample tap at the end of the sampling period and record the date, time of day, and final gallon (or cubic feet) reading from the water meter onto the Sample Data Sheet. Although the final water meter reading may be affected by the addi- tion of HCl and/or thiosulfate, the effect is considered insignificant and may be ignored.
Step 15. Loosen the swivel female insert on the regulator module and disconnect the backflow regulator from the tap. Disconnect the cartridge housing module and the prefilter housing module, if used from the other modules. Turn the filter housing(s) upside down and allow excess water to flow out as waste water. Turn the housing(s) upright and cover the quick connects on each end of the modules with sterile aluminum foil.
Step 16. Pack the cartridge housing module(s) into an insulated shipping box. Add 6-8 small ice packs (prefrozen at -20 C) around the cartridge housings to keep the sample cool in transit (the number of ice packs may have to be adjusted based upon experience to ensure that the samples remain cold, but not frozen). Drain and add the regulator and injector modules used. Place the Sample Data Sheet (protected with a closable plastic bag) in with the sample and ship by overnight courier to the contracted, approved laboratory for virus analysis. Notify the laboratory by phone upon the shipment of sample.
The approved laboratory will elute virus from the 1MDS filter (and prefilter, if appropri- ate) and analyze the eluates as described in Parts 2-3. After removing the filter, the laboratory will clean, sterilize the apparatus components with chlorine and dechlorinate with sodium thiosulfate as described in Part 5. After flushing with sterile dH2O, a new 1MDS cartridge (and prefilter, if appropriate) will be added, the openings sealed with sterile aluminum foil, and the apparatus returned to the utility for the next sample. The discharge module can be stored at the utility between samplings. Openings should be covered with aluminum foil during storage.
VIII-15
PART 2 — SAMPLE PROCESSING
QUALITY CONTROL AND PERFORMANCE EVALUATION SAMPLES
Quality control (QC) and performance evaluation (PE) samples will be shipped to analysts seeking approval (see Sections III-IV). PE samples must be successfully analyzed by each analyst participating in the ICR virus monitoring program as part of the initial approval process. After initial approval, each analyst must successfully analyze one QC sample set per sample batch and one PE sample set every month. A QC sample set is comprised of a negative and a positive QC sample. A sample batch consists of all the ICR samples that are analyzed by an analyst during a single week. Each sample batch and its associated QC sample set must be assigned a unique batch number. QC samples do not have to be processed during weekly periods when no ICR samples are processed. QC and PE data should be sent directly to the
U.S. EPA as specified in Section III.
QC Samples:
- Negative QC Sample: Place a sterile 1MDS filter into a standard filter apparatus.
Process and analyze the 1MDS filter using the Elution, Organic Flocculation and Total Culturable Virus Assay procedures given below.
- Positive QC Sample: Place 40 L of dH2O into a sterile polypropylene container (Cole- Parmer Product No. G-06063-32) and add 1 mL of a QC stock of attenuated poliovirus containing 200 PFU/mL2. Mix and pump the water through a standard filter apparatus containing a 1MDS filter.
Process and analyze the 1MDS filter using the Elution, Organic Flocculation and Total Culturable Virus Assay procedures given below.
PE Samples:
Process and analyze PE samples according to the Elution, Organic Flocculation and Total Culturable Virus Assay procedures of this protocol and according to any additional procedures supplied with the samples.
2A QC sample with a titer of 200 PFU/mL will be supplied for the QC tests described in this Section. The titer of this QC sample may be changed before the start or during the testing phase of the ICR. Analysts must use these samples as supplied and not attempt to adjust the titer to 200 PFU/mL. A high titer QC sample will also be shipped to each analyst so that laboratories can develop their own internal QC programs. The high titered sample is not to be used for the QC tests described in this Section.
VIII-16
ELUTION PROCEDURE
The cartridge filters must arrive from the utility in a refrigerated, but not frozen, condi- tion. The arrival condition should be recorded on the Sample Data Sheet (Part 9). Filters should be refrigerated upon arrival and eluted within 72 h of the start of the sample collection.
Apparatus and Materials:
- Positive pressure air or nitrogen source equipped with a pressure gauge.
If the pressure source is a laboratory air line or pump, it must be equipped with an oil filter.
- Dispensing pressure vessels — 5 or 20 liter capacity (Millipore Corp. Product No. XX67 00P 05 and XX67 00P 20).
- pH meter with combination-type electrode and an accuracy of at least 0.1 pH unit.
- Autoclavable inner-braided tubing with screw clamps or quick connects for connecting tubing to equipment.
- Magnetic stirrer and stir bars.
Media and Reagents:
- Sodium hydroxide (NaOH) — prepare 1 M and 5 M solutions by dissolving 4 g or 20 g of NaOH in a final volume of 100 mL of dH2O, respectively.
NaOH solutions may be stored for several months at room temperature.
- Beef extract V powder (BBL Microbiology Systems Product No. 97531) — prepare buffered 1.5% beef extract by dissolving 30 g of beef extract powder and 7.5 g of glycine (final glycine concentration = 0.05 M) in 1.9 L of dH2O. Adjust the pH to 9.5 with 1 or 5 M NaOH and bring the final volume to 2 L with dH2O. Autoclave at 121 C for 15 min and use at room temperature.
Beef extract solutions may be stored for one week at 4 C or for longer periods at -20 C. Screen each new lot of beef extract before use in the Organic Flocculation Concentration
Procedure to determine whether virus recoveries are adequate. Perform the screening by spiking one liter of beef extract solution with 1 mL of a diluted QC sample containing 200 PFU/mL. Assay the spiked sample according to the Organic Flocculation and Total Culturable Virus Assay procedures given below. Use a single passage with undiluted sample and sample diluted 1:5 and 1:25 along with an equivalent positive control. The mean recovery of poliovirus for three trials should be at least 50%.
VIII-17
Procedure:
Place a disinfectant-soaked sponge over vents while releasing trapped air or pressure throughout this procedure to minimize dangers from aerosols.
Step 1. Attach sections of braided tubing (sterilized on inside and outside surfaces with chlorine and dechlorinated with thiosulfate as described in Part 5) to the inlet and outlet ports of a cartridge housing module containing a 1MDS filter to be tested for viruses. If a prefilter was used, keep the prefilter and cartridge housing modules connected and attach the tubing to the inlet of the prefilter module and to the outlet of the cartridge housing module.
Step 2. Place the sterile end of the tubing connected to the outlet of the cartridge housing module into a sterile two liter glass or polypropylene beaker.
Step 3. Connect the free end of the tubing from the inlet port of the prefilter or cartridge housing modules to the outlet port of a sterile pressure vessel and connect the inlet port of the pressure vessel to a positive air pressure source. Add pressure to blow out any residual water from the cartridge housing(s). Open the vent/relief valve to release the pressure.
Step 4. Remove the top of the pressure vessel and pour 1000 mL of buffered 1.5% beef extract (pH 9.5, prewarmed to room temperature) into the vessel. Replace the top of the pressure vessel and close its vent/relief valve.
Acceptable alternatives to the use of a pressure vessel include 1) the use of a peristaltic pump and sterile tubing to push the beef extract through the filter and 2) the addition of beef extract directly to the cartridge housing and the use of positive pressure to push the beef extract through the filter.
Step 5. Open the vent/relief valve(s) on the cartridge housing(s) and slowly apply sufficient pressure to purge trapped air from them. Close the vent/relief valve(s) as soon as the buffered beef extract solution begins to flow from it. Turn off the pressure and allow the solution to contact the 1MDS filter for 1 min.
Wipe up spilled liquid with disinfectant-soaked sponge. Carefully observe alternative housings without vents to ensure that all trapped air has been purged.
Step 6. Increase the pressure to force the buffered beef extract solution through the filter(s).
The solution should pass through the 1MDS filter slowly to maximize the elution contact period. When air enters the line from the pressure vessel, elevate and invert the filter housing to permit complete evacuation of the solution from the filters.
Step 7. Turn off the pressure at the source and open the vent/relief valve on the pressure vessel. Place the buffered beef extract from the two liter beaker back into the pressure vessel. Replace the top of the pressure vessel and close its vent/relief valve. Repeat Steps 5 – 6.
VIII-18
Step 8. Turn off the pressure at the source and open the vent/relief valve on the pressure vessel. Thoroughly mix the eluate. Adjust the pH of the eluate to 7.0-7.5 with 1 M HCl. If archiving is not required and if the optional coliphage assay is not performed, measure the volume of the eluate and record it onto the Virus Data Sheet as the Eluate Volume Recov- ered. Transfer the Total Sample Volume from the Sample Data Sheet to the Adjusted Total Sample Volume on the Virus Data Sheet.
Step 9. If archiving is required or if the optional coliphage assay (see Section IX. Coliphage Assay) will be performed, adjust the pH of the eluate to 7.0-7.5 with 1 M HCl. Measure the volume of the adjusted eluate and record it onto the Virus Data Sheet as the Eluate Volume Recovered. Determine the amount of sample to be used in the coliphage assay by multiplying the Eluate Volume Recovered by 0.035. Place a volume equal to the product obtained into a separate container and store at 4 C. If archiving is not required, multiply the Total Sample Volume from the Sample Data Sheet by 0.965 and record the product as the Adjusted Total Sample Volume on the Virus Data Sheet.
Step 10. If archiving is required, determine the amount of sample to remove for archiving by multiplying the Eluate Volume Recovered by 0.1. Record the product onto the Virus Data Sheet as the Volume of Eluate Archived and place this volume into a separate container.
Freeze3 the archive sample and ship it to the ICR Laboratory Coordinator, USEPA, TSD, 26
- Martin Luther King Drive, Cincinnati, OH 45268. Multiply the Total Sample Volume from the Sample Data Sheet by 0.865 if the optional coliphage assay is performed or by 0.9 if the sample was not assayed for coliphage. Record the product as the Adjusted Total Sample Volume on the Virus Data Sheet.
Step 11. Proceed to the Organic Flocculation Concentration Procedure immediately. If the Organic Flocculation Concentration Procedure cannot be undertaken immediately, store the eluate (adjusted to pH 7.0 to 7.5 as described in Step 8b) at 4 C for up to 24 h or for longer periods at -70 C.
ORGANIC FLOCCULATION CONCENTRATION PROCEDURE
Apparatus and Materials:
- Refrigerated centrifuge capable of attaining 2,500 – 10,000 ×g and screw-capped centri- fuge bottles with 100 to 1000 mL capacity.
3All freezing of samples and cell cultures throughout this protocol should be performed rapidly by placing vessels in a freezer at -70 C or below or in a dry ice-alcohol bath. Frozen samples and cell cultures should also be thawed rapidly. This may be done by placing vessels in a 37 C waterbath, but vessel caps must not be immersed and vessels should be removed from the waterbath as soon as or just before the last ice crystals melt.
VIII-19
Each bottle must be rated for the relative centrifugal force used.
- Sterilizing filter — 0.22 µm Acrodisc filter with prefilter (Gelman Sciences Product No. 4525).
Use sterilizing filter stacks on samples that clog commercial filters. Prepare sterilizing filter stacks using 0.22 µm pore size membrane filters (Millipore Corp. Product No.
GSWP 47 00) stacked with fiberglass prefilters (Millipore Corp. AP15 47 00 and AP20 47 00). Stack the prefilters and 0.22 µm membrane into a disc filter holder (Millipore Corp. Pro-
duct No. SX00 47 00) with the AP20 prefilter on top and 0.22 µm membrane filter on bottom. Disassemble the filter stack after each use to check the integrity of the 0.22 µm filter. Refilter any media filtered with a damaged stack.
Always pass about 10 – 20 mL of sterile beef extract, pH 7.0-7.5 (prepared as above, without pH adjustment), through the filter just before use. This step will reduce virus adsorp- tion onto the filter membranes.
Media and Reagents:
- Sodium phosphate, dibasic (Na2HPO4 7H2O) — 0.15 M, pH 9.0 – 9.5 or 7.0 – 7.5.
Dissolve 40.2 g of sodium phosphate in a final volume of 1000 mL dH2O. The pH of the solution should be between 9.0 – 9.5. Adjust the pH to 9.0 to 9.5 with NaOH, if necessary, or to
7.0 to 7.5 with HCl. Autoclave at 121 C for 15 min.
Procedure:
Minimize foaming (which may inactivate viruses) throughout the procedure by not stirring or mixing faster than necessary to develop a vortex.
Step 1. Place a sterile stir bar into the beaker containing the buffered beef extract eluate from the cartridge filter(s). Place the beaker onto a magnetic stirrer, and stir at a speed sufficient to develop a vortex.
Step 2. Insert a combination-type pH electrode into the beef extract eluate. Add 1 M HCl to the eluate slowly while moving the tip of the pipette in a circular motion away from the vortex to facilitate mixing. Continue adding 1 M HCl until the pH reaches 3.5 ± 0.1 and then stir slowly for 30 min at room temperature.
The pH meter must be standardized at pH 4 and 7. Electrodes must be sterilized before and after each use as described in Part 5.
A precipitate will form. If pH falls below 3.4, add 1 M NaOH to bring it back to 3.5 ± 0.1.
Exposure to a pH below 3.4 may result in some virus inactivation.
Step 3. Remove the electrode from the beaker, and pour the contents of the beaker into a centrifuge bottle. Cap the bottle and centrifuge the precipitated beef extract suspension at 2,500 ×g for 15 min at 4 C. Remove and discard the supernatant.
VIII-20
To prevent the transfer of the stir bar into a centrifuge bottle, hold another stir bar or magnet against the bottom of the beaker while decanting the contents. The beef extract suspension will usually have to be divided into several centrifuge bottles.
Step 4. Place a stir bar into the centrifuge bottle that contains the precipitate. Add 30 mL of
0.15 M sodium phosphate, pH 9.0 – 9.5. Place the bottle onto a magnetic stirrer, and stir slowly until the precipitate has dissolved completely.
Since the precipitate may be difficult to dissolve, it can be partially dispersed with a spatula before or during the stirring procedure. It may also be dissolved by repeated pipetting or by shaking at 160 rpm for 20 min on an orbital shaker in place of stirring. When the centrifugation is performed in more than one bottle, dissolve the precipitates in a total of 30 mL and combine into one bottle. If the precipitate is not completely dissolved before proceed- ing, significant virus loss may occur in Step 5. Because virus loss may also occur by pro- longed exposure to pH 9.0-9.5, laboratories that find it difficult to resuspend the precipitate may dissolve it initially in 0.15 M sodium phosphate, pH 7.0 – 7.5. If this variation is used, the pH should be re-adjusted to 9.0-9.5 with 1 M NaOH after the precipitate is completely dissolved and mixed for 10 min at room temperature before proceeding to Step 5.
Step 5. Check the pH and readjust to 9.0-9.5 with 1 M NaOH, as necessary. Remove the stir bar and centrifuge the dissolved precipitate at 4,000 – 10,000 ×g for 10 min at 4 C. Remove the supernatant and discard the pellet. Adjust the pH of the supernatant to 7.0-7.5 with 1 M HCl. To remove microbial contamination, load the supernatant into a 50 mL syringe and force it through a sterilizing filter pretreated with beef extract (laboratories may use other ap- proaches to remove contamination, but their effectiveness must be documented). Record the final supernatant (designated the Final Concentrated Sample Volume ; FCSV) on the Virus Data Sheet (see Part 9).
If the sterilizing filter begins to clog badly, empty the loaded syringe into the bottle containing the unfiltered supernatant, fill the syringe with air, and inject air into filter to force any residual sample from it. Continue the filtration procedure with another filter.
Step 6. Determine the volume of sample that must be assayed. This volume is at least 100 L for source water or 1000 L for finished water and is designated the Volume of Original Water Sample Assayed4 (D). Record the value of D on the Virus Data Sheet. Calculate the Assay Sample Volume (S) for source and finished water samples using the formula:
S D ATSV
× FCSV
4Analytical laboratories assaying more than the required volume must use the actual volume to be assayed in the calculation. See Part 8 for examples of the calculations used in this protocol.
VIII-21
where ATSV is the Adjusted Total Sample Volume from the Virus Data Sheet. The Assay Sample Volume is the volume of the Final Concentrated Sample that represents 100 L of source water or 1000 L of finished water. Record the Assay Sample Volume onto the Virus Data Sheet. Prepare a subsample (subsample 1) containing a volume 0.55 times the Assay Sample Volume. Prepare a second subsample (subsample 2) containing a volume that is 0.67 times the Assay Sample Volume. Divide the Final Concentrated Sample from QC and PE samples into two equal subsamples. Calculate the Assay Sample Volume for these samples by multiplying FCSV by 0.4. Label each subsample with appropriate sampling information for identification. Hold any portion of the sample that can be assayed within 24 h at 4 C and freeze all other portions at -70 C.
Final Concentrated Samples, subsamples, PE and QC samples processed to this point by a laboratory not doing the virus assay must be frozen at -70 C immediately and then shipped on dry ice to the laboratory approved for the virus assay.
VIII-22
PART 3 — TOTAL CULTURABLE VIRUS ASSAY
QUANTAL ASSAY
Apparatus and Materials:
- Incubator capable of maintaining the temperature of cell cultures at 36.5 ± 1 C.
- Sterilizing filter — 0.22 µm (Costar Product No. 140666).
Always pass about 10 – 20 mL of 1.5% beef extract, pH 7.0-7.5, through the filter just before use to minimize virus adsorption to the filter.
Media and Reagents:
- Prepare BGM cell culture test vessels using standard procedures.
BGM cells are a continuous cell line derived from African Green monkey kidney cells and are highly susceptible to many enteric viruses (Dahling et al., 1984; Dahling and Wright, 1986). The characteristics of this line were described by Barron et al. (1970). The use of BGM cells for recovering viruses from environmental samples was described by Dahling et al. (1974). For laboratories with no experience with virus recovery from environmental samples, the media and procedures described by Dahling and Wright (1986) and given in Part 4 are recommended for maximum sensitivity.
EPA will supply an initial culture of BGM cells at about passage 117 to all laboratories seeking approval. Upon receipt, laboratories must prepare an adequate supply of frozen BGM cells using standard procedures to replace working cultures that become contaminated or lose virus sensitivity. A Procedure for Preservation of the BGM Cell Line is given in Part
- 4. Only BGM cells from the U.S. EPA and between passage 117 and 250 may be used for virus monitoring under the ICR.
Sample Inoculation and CPE Development:
Cell cultures used for virus assay are generally found to be at their most sensitive level between the third and sixth days after their most recent passage. Those older than seven days should not be used.
Step 1. Identify cell culture test vessels by coding them with an indelible marker. Return the cell culture test vessels to a 36.5 ± 1 C incubator and hold at that temperature until the cell monolayer is to be inoculated.
Step 2. Decant and discard the medium from cell culture test vessels. Wash the test vessels with a balanced salt solution or maintenance medium without serum using a wash volume of at least 0.06 mL/cm2 of surface area. Rock the wash medium over the surface of each monolayer several times and then decant and discard the wash medium.
Do not disturb the cell monolayer.
VIII-23
Step 3. Determine the Inoculum Volume by dividing the Assay Sample Volume by 20. Record the Inoculum Volume onto the Virus Data Sheet. The Inoculum Volume should be no greater than 0.04 mL/cm2 of surface area. If the Inoculum Volume is greater than 0.04 mL/cm2, use larger culture vessels.
Step 4. Inoculate each BGM cell culture test vessel with an amount of assay control or water sample equal to the Inoculum Volume and record the date of inoculation on the Sample Data Sheet (see Part 9).
Avoid touching either the cannula or the pipetting device to the inside rim of the cell culture test vessels to avert the possibility of transporting contaminants to the remaining culture vessels.
For ease of inoculation, a sufficient quantity of 0.15 M Na2HPO4, pH 7.0 – 7.5, may be added to the Inoculum Volume to give a more usable working Inoculation Volume (e.g., 1.0 mL). For example, if an Inoculum Volume of 0.73 mL is to be placed onto 10 vessels, then
- 5 × (1 – 0.73 mL) = 2.84 mL of sodium phosphate, pH 7.0-7.5 could be added to 10.5 ×
0.73 = 7.67 mL of subsample. Each milliliter of the resulting mixture will contain the required
Inoculum Volume.
- Total Culturable Virus Assay Controls:
Run a negative and positive assay control with every group of subsamples inoculated onto cell cultures.
- Negative Assay Control: Inoculate a BGM culture with a volume of sodium phosphate, pH 7.0 – 7.5, equal to the Inoculation Volume. This culture will serve as negative control for the tissue culture quantal assay. If any Negative Assay Control develops cytopathic effects (CPE), all subsequent assays of water samples should be halted until the cause of the positive result is deter- mined.
- Positive Assay Control: Dilute attenuated poliovirus type 3 (from the high titered QC stock) in sodium phosphate, pH 7.0 – 7.5, to give a concentration of 20 PFU per Inoculation Volume. Inoculate a BGM culture with an amount of diluted virus equal to the Inoculation Volume. This control will provide a measure for continued sensitivity of the cell cultures to virus infection. Addi- tional positive control samples may be prepared by adding virus to a small portion of the final concentrated sample and/or by using additional virus types. If any Positive Assay Control fails to develop CPE, all subsequent assays of water samples should be halted until the cause of the negative result is deter- mined. It may be necessary to thaw and use an earlier passage of the BGM cell line supplied by the U.S. EPA.
VIII-24
- Inoculation of Water Samples
- Rapidly thaw subsample 1, if frozen, and inoculate an amount equal to the Inoculum Volume onto each of 10 cell cultures. If there is no evidence for cytotoxicity and if at least three cell cultures are negative for CPE after seven days (see below), thaw subsample 2 and inoculate an amount equal to the Inoculum Volume onto each of 10 additional cultures.
Hold a thawed subsample for no more than 4 h at 4 C. Warm the subsam- ple to room temperature just before inoculation.
A small portion of the Final Concentrated Sample may by inoculated onto cultures several days before inoculating subsample 1 as a control for cytotoxic- ity.
- If cytotoxicity is not a problem and more than seven cultures are positive for CPE after seven days, prepare five- and twenty five-fold dilutions of subsample
- To prepare a 1:5 dilution, add a volume equal to 0.1334 times the Assay Sample Volume (amount “a”) to a volume of 0.15 M sodium phosphate (pH 7.0-7.5) equal to 0.5334 times the Assay Sample Volume (amount “b”). After mixing thoroughly, prepare a 1:25 dilution by adding amount “a” of the 1:5 diluted sample to amount “b” of 0.15 M sodium phosphate (pH 7.0-7.5). Using an amount equal to the Inoculum Volume, inoculate 10 cell cultures each with undiluted subsample 2, subsample 2 diluted 1:5 and subsample 2 diluted 1:25, respectively. Freeze the remaining portions of the 1:25 dilution at -70 C until the sample results are known. If the inoculated cultures are all positive, thaw the remaining 1:25 dilution and prepare 1:125, 1:625 and 1:3125 dilutions by transferring amount “a” of each lower dilution to amount “b” of sodium phos- phate as described above. Inoculate 10 cultures each with the additional dilu- tions and freeze the remaining portion of the 1:3125 dilution. Continue the process of assaying higher dilutions until at least one test vessel at the highest dilution tested is negative. Higher dilutions can also be assayed along with the initial undiluted to 1:25 dilutions if it is suspected that the water to be tested contains more than 500 most probable number (MPN) of infectious total culturable virus units per 100 L.
- If subsample 1 is cytotoxic, then five cell cultures should be inoculated with Final Concentrated Sample using the same volume required for subsample 1 and the procedures described in the Reduction of Cytotoxicity in Sample Concen- trates section below. If these procedures remove cytotoxicity, inoculate subsample 2 using the procedures for removal of cytotoxicity and 10 cultures each with undiluted sample, sample diluted 1:5 and sample diluted 1:25 as in Step 4bii above. If the procedures fail to remove cytotoxicity, write for advice on how to proceed to the ICR Laboratory Coordinator, U.S. EPA, Office of Ground Water and Drinking Water, Technical Support Division, 26 W. Martin Luther King Drive, Cincinnati, OH 45268.
VIII-25
A maximum of 60 and 580 MPN units per 100 L can be demonstrated by inoculating a total of 20 cultures with the undiluted Assay Sample Volume from source water or a total of 10 cultures each with undiluted sample and sample diluted 1:5 and 1:25, respectively.
- Inoculation of QC and PE Samples: prepare five-fold dilutions of subsample 1 for each negative QC sample as described in Step 4bii. Prepare five- and twenty five-fold dilutions for each positive QC and PE sample. Inoculate 10 cultures with undiluted subsample and each diluted subsample using an amount of inoculum equal to the Inoculum Volume.
Use subsample 2 only as a backup for problems with the analysis of subsample 1.
Step 5. Rock the inoculated cell culture test vessels gently to achieve uniform distribution of inoculum over the surface of the cell monolayers. Place the cell culture test vessels on a level stationary surface at room temperature so that the inoculum remains distributed evenly over the cell monolayer.
Step 6. Continue incubating the inoculated cell cultures for 80 – 120 min to permit viruses to adsorb onto and infect cells.
It may be necessary to rock the vessels every 15-20 min or to keep them on a mechanical rocking platform during the adsorption period to prevent cell death in the middle of the vessels from dehydration.
Step 7. Add liquid maintenance medium (see Item 2 of Vessels and Media for Cell Growth
in Part 4 for recommended medium) and incubate at 36.5 ± 1 C.
Warm the maintenance medium to 36.5 ± 1 C before placing it onto cell monolayers.
Add the medium to the side of the cell culture vessel opposite the cell monolayer. Avoid touching any pipetting devices used to the inside rim of the culture vessels to avert the possibility of transporting contaminants to the remaining vessels. The cultures may be re-fed with fresh maintenance medium after 4 – 7 days.
Step 8. Examine each culture microscopically for the appearance of CPE daily for the first three days and then every couple of days for a total of 14 days.
CPE may be identified as cell disintegration or as changes in cell morphology. Round- ing-up of infected cells is a typical effect seen with enterovirus infections. However, uninfected cells round-up during mitosis and a sample should not be considered positive unless there are significant clusters of rounded-up cells over and beyond what is observed in the uninfected controls. Photomicrographs demonstrating CPE appear in the reference by Malherbe and Strickland-Cholmley (1980).
Step 9. Freeze cultures at -70 C when more than 75% of the monolayer shows signs of CPE. Freeze all remaining negative cultures, including controls, after 14 days.
VIII-26
Step 10. Thaw all the cultures to confirm the results of the previous passage. Filter at least 10% of the medium from each vessel that was positive for CPE or that appeared to be bacterially contaminated through separate 0.22 µm sterilizing filters. Then inoculate another BGM culture with 10% of the medium from the previous passage for each vessel, including those that were negative. Repeat Steps 7 – 8.
Confirmation passages may be performed in small vessels or multiwell trays, however, it may be necessary to distribute the inoculum into several vessels or wells to insure that the Inoculum Volume is less than or equal to 0.04 mL/cm2 of surface area.
Step 11. Score cultures that developed CPE in both the first and second passages as confirmed positives. Cultures that show CPE in only the second passage must be passaged a third time along with the negative controls according to Steps 9 – 10. Score cultures that develop CPE in both the second and third passages as confirmed positives.
Cultures with confirmed CPE may be stored in a -70 C freezer for research purposes or for optional identification tests.5
Virus Quantitation:
Step 1. Record the total number of confirmed positive and negative cultures for each subsample onto the Total Culturable Virus Data Sheet (Part 9). Do not include the results of tests for cytotoxicity!
Step 2. Transfer the number of cultures inoculated and the confirmed number of positive cultures from the Total Culturable Virus Data Sheet for each subsample to the Quantitation of Total Culturable Virus Data Sheet . If dilutions are not required, add the values to obtain a total undiluted count for each sample. Calculate the MPN/mL value (Mm) and the upper (CLum) and lower (CLlm) 95% confidence limits using the total undiluted count. If dilutions are required, calculate the MPN/mL value and 95% confidence limits using only the subsample 2 values. Place the values obtained onto the Quantitation of Total Culturable Virus Data Sheet. The MPNV computer program supplied by the U.S. EPA must be used for the calculation of all MPN values and confidence limits.
Step 3. Calculate the MPN per 100 liter value (Ml) of the original water sample according the formula:
M 100 Mm S
l D
5For more information see Chapter 12 (May 1988 revision) of Berg et al. (1984).
VIII-27
where S equals the Assay Sample Volume and D equals the Volume of Original Water Sample Assayed (the values for S and D can be found on the Virus Data Sheet). Record the value of Ml onto the Virus Data Sheet.
Step 4. Calculate the lower 95% confidence limit per 100 liter value (CLl) for each water sample according to the formula:
CLl
100 CLlmS D
where CLlm is the lower 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet. Calculate the upper 95% Confidence Limit per 100 liter value (CLu) according to the formula:
CLu
100 CLumS D
where CLum is the upper 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet. Record the limit per 100 liter values on the Virus Data Sheet.
Step 5. Calculate the total MPN value and the total 95% confidence limit values for each QC and PE sample by multiplying the values per milliliter by S and dividing by 0.4.
REDUCTION OF CYTOTOXICITY IN SAMPLE CONCENTRATES
The procedure described in this section may result in a significant titer reduction and should be applied only to inocula known to be or expected to be toxic.
Media and Reagents:
- Washing solution.
Dissolve 8.5 g of NaCl in a final volume of 980 mL of dH20. Autoclave the solution at 121 C for 15 min. Cool to room temperature. Add 20 mL serum to the sterile salt solution. Mix thoroughly. Store the washing solution at 4 C for up to three months or at -20 C.
The volume of the NaCl washing solution required will depend on the number of bottles to be processed and the cell surface area of the vessels used for the quantal assay.
6Use significant figures when reporting all results throughout the protocol (see APHA, 1995, p. 1-17).
VIII-28
Procedure for Cytotoxicity Reduction:
Step 1. Decant and save the inoculum from inoculated cell culture vessels after the adsorp- tion period (Step 5 of Sample Inoculation and CPE Development ). Add 0.25 mL of the washing solution for each cm2 of cell surface area into each vessel.
Warm the washing solution to 36.5 ± 1 C before placing on cell monolayer. Add the washing solution to the side of the cell culture vessel opposite the cell monolayer. Avoid touching any pipetting devices used to the inside rim of the culture vessels to avert the possibility of transporting contaminants to the remaining vessels.
The inocula saved after the adsorption period should be stored at -70 C for subsequent treatment and may be discarded when cytotoxicity is successfully reduced.
Step 2. Gently rock the washing solution gently across the cell monolayer a minimum of two times. Decant and discard the spent washing solution without disturbing the cell monolayer.
It may be necessary to rock the washing solution across the monolayer more than twice if sample is oily and difficult to remove from the cell monolayer surface.
Step 3. Continue with Step 7 of the procedure for Sample Inoculation and CPE Develop- ment.
If this procedure fails to reduce cytotoxicity with a particular type of water sample, backup samples may be diluted 1:2 to 1:4 before repeating the procedure. This dilution requires that two to four times more culture vessels be used. Dilution alone may sufficiently reduce cytotoxicity of some samples without washing. Alternatively, the changing of liquid maintenance medium at the first signs of cytotoxicity may prevent further development.
Determine cytotoxicity from the initial daily macroscopic examination of the appearance of the cell culture monolayer by comparing the negative control from Step 4ai and the positive control from Step 4aii of the procedure for Sample Inoculation and CPE Development with the test samples from Step 4b). Cytotoxicity should be suspected when the cells in the test sample develop CPE before its development on the positive control.
VIII-29
PART 4 — CELL CULTURE PREPARATION AND MAINTENANCE
PREPARATION OF CELL CULTURE MEDIUM
General Principles:
- Equipment care — Carefully wash and sterilize equipment used for preparing media before each use.
- Disinfection of work area — Thoroughly disinfect surfaces on which the medium preparation equipment is to be placed.
- Aseptic technique — Use aseptic technique when preparing and handling media or medium components.
- Dispensing filter-sterilized media — To avoid post-filtration contamination, dispense filter-sterilized media into storage containers through clear glass filling bells in a microbiolog- ical laminar flow hood. If a hood is unavailable, use an area restricted solely to cell culture manipulations.
- Coding media — Assign a lot number to and keep a record of each batch of medium or medium components prepared. Place the lot number, the date of preparation, the expiration date, and the initials of the person preparing the medium on each bottle.
- Sterilization of NaHCO3-containing solutions — Sterilize media and other solutions that contain NaHCO3 by positive pressure filtration.
Negative pressure filtration of such solutions increases the pH and reduces the buffering capacity.
- Antibiotic solutions prepared in-house must be filter sterilized with 0.22 µm membrane filters. It is important that the recommended antibiotic levels not be exceeded during the planting of cells, as cultures are particularly sensitive to excessive concentrations at this stage. Antibiotic stock solutions should be placed in screw-capped containers and stored at -20 C until needed. Once thawed, they may be refrozen; however, repeated freezing and thawing of these stock solutions should be avoided by freezing them in quantities that are sufficient to support a week’s cell culture work.
Apparatus and Materials:
- Glassware, Pyrex (Corning Product No. 1395).
Storage vessels must be equipped with airtight closures.
VIII-30
- Disc filter holders — 142 mm or 293 mm diameter (Millipore Product No. YY30 142 36 and YY30 293 16).
Use only positive pressure type filter holders.
- Sterilizing filter stacks — 0.22 µm pore size (Millipore Product No. GSWP 142 50 and GSWP 293 25). Fiberglass prefilters (Millipore AP15 142 50 or AP15 293 25, and AP20 142 50 or AP20 293 25).
Stack AP20 and AP15 prefilters and 0.22 µm membrane filter into a disc filter holder with AP20 prefilter on top and 0.22 µm membrane filter on bottom.
Always disassemble the filter stack after use to check the integrity of the 0.22 µm filter.
Refilter any media filtered with a damaged stack.
- Positively-charged cartridge filter — 10 inch (Zeta plus TSM, Cuno Product No.
45134-01-600P). Cartridge housing with adaptor for 10 inch cartridge (Millipore Product No. YY16 012 00).
- Culture capsule filter (Gelman Sciences Product No. 12170).
- Cell culture vessels — Pyrex, soda or flint glass or plastic bottles and flasks or roller bottles (e.g., Brockway Product No. 1076-09A, 1925-02, Corning Product No. 25100-25, 25110-75, 25120-150, 25150-1750).
Vessels must be made from clear glass or plastic to allow observation of the cultures and be equipped with airtight closures. Plastic vessels must be treated by the manufacturer to allow cells to adhere properly.
- Screw caps, black with rubber liners (Brockway Product No. 24-414).
Caps for larger culture bottles usually supplied with bottles.
- Roller apparatus (Bellco Glass Product No. 7730).
Required only if roller bottles are used for maintenance of stock cultures.
- Waterbath set at 56 ± 1 C.
- Light microscope, with conventional light source, equipped with lenses to provide 40X, 100X, and 400X total magnification.
- Inverted light microscope equipped with lenses to provide 40X, 100X, and 400X total magnification.
- Phase contrast counting chamber (hemocytometer) (Curtin Matheson Scientific Product No. 158-501).
- Conical centrifuge tubes — 50 and 250 mL capacity.
VIII-31
- Rack for tissue culture tubes (Bellco Product No. 2028).
- Bottles, aspirator-type with tubing outlet — 2,000 mL capacity.
Bottles for use with pipetting machine.
- Storage vials — 2 mL capacity.
Vials must withstand temperatures to -70 C.
Media and Reagents:
- Sterile fetal calf, gamma globulin-free newborn calf or iron-supplemented calf serum, certified free of viruses, bacteriophage and mycoplasma.
Test each lot of serum for cell growth and toxicity before purchasing. Serum should be stored at -20 C for long-term storage. Upon thawing, each bottle must be heat-inactivated in a waterbath set at 56 ± 1 C for 30 min and stored at 4 C for short term use.
- Trypsin, 1:250 powder (Difco Laboratories Product No. 0152-15-9) or trypsin, 1:300 powder (Becton Dickinson Microbiology Systems Product No. 12098).
- EDTA (Fisher Scientific Product No. S657-500).
- Fungizone (amphotericin B, Sigma Product No. A-9528), penicillin G (Sigma Product No. P-3032), streptomycin sulfate (ICN Biomedicals Product No. 100556), tetracycline hydrochloride (ICN Biomedicals Product No. 103011).
Use antibiotics of at least tissue culture grade.
- Eagle’s minimum essential medium (MEM) with Hanks’ salts and L-glutamine, without sodium bicarbonate (Life Technologies Product No. 410-1200).
- Leibovitz’s L-15 medium with L-glutamine (Life Technologies Product No. 430-1300).
- Trypan blue (Sigma Chemical Product No. T-6146).
- Dimethyl sulfoxide (DMSO; Sigma Chemical Product No. D-2650).
Media Preparation Recipes:
The conditions specified by the supplier for storage and expiration dates of commercially available media should be strictly observed.
- Procedure for the preparation of 10 L of EDTA-trypsin.
The procedure described is used to dislodge cells attached to the surface of culture bottles and flasks. This reagent, when stored at 4 C, retains its working strength for at least four
VIII-32
months. The amount of reagent prepared should be based on projected usage over a four month period.
Step a. Add 30 g of trypsin (1:250) or 25 g of trypsin (1:300) to 2 L of dH2O in a six liter flask containing a three inch stir bar. Place the flask onto a magnetic stirrer and mix the trypsin solution rapidly for a minimum of 1 h.
The trypsin remains cloudy.
Step b. Add 4 L of dH2O and a three-inch stir bar into a 20 liter clear plastic carboy. Place the carboy onto a magnetic stirrer and stir at a speed sufficient to develop a vortex while adding the following chemicals: 80 g NaCl, 12.5 g EDTA, 50 g glucose, 11.5 g
Na2HPO4 7H2O, 2.0 g KCl, and 2.0 g KH2PO4.
Each chemical does not have to be completely dissolved before adding the next one.
Step c. Add an additional 4 L dH2O to the carboy and continue mixing until all the chemicals are completely dissolved.
Step d. Add the 2 L of trypsin from Step 2a to the solution from Step 2c and mix for a minimum of 1 h. Adjust the pH of the EDTA-trypsin reagent to 7.5 – 7.7.
Step e. Filter the reagent under pressure through a filter stack and store the filtered reagent in tightly stoppered or capped containers at 4 C.
The cartridge prefilter (Item 4 of Apparatus and Materials) can be used in line with the culture capsule sterilizing filter (Item 5) as an alternative to a filter stack (Item 3).
- Procedure for the preparation of 10 L of MEM/L-15 medium.
Step a. Place a three inch stir bar and 4 L of dH2O into a 20 liter clear plastic carboy.
Step b. Place the carboy onto a magnetic stirrer. Stir at a speed sufficient to develop a vortex and then add the contents of a five liter packet of L-15 medium to the carboy.
Rinse the medium packet with three washes of 200 mL each of dH2O and add the rinses to the carboy.
Step c. Mix until the medium is evenly dispersed.
L-15 medium may appear cloudy as it need not be totally dissolved before proceed- ing to Step d.
Step d. Add 3 L of dH2O to the carboy and the contents of a five liter packet of MEM medium to the carboy. Rinse the MEM medium packet with three washes of 200 mL each of dH2O and add the rinses to the carboy. Add 800 mL of dH2O and 7.5 g of NaHCO3 and continue mixing for an additional 60 min.
VIII-33
Step e. Transfer the MEM/L-15 medium to a pressure can and filter under positive pressure through a 0.22 µm sterilizing filter. Collect the medium in volumes appropriate for the culturing of BGM cells (e.g., 900 mL in a one liter bottle) and store in tightly stoppered or capped containers at 4 C for up to two months.
Note that the volume of the MEM/L-15 medium adds up to only 9 L to allow for the addition of serum to a final concentration of 10%.
- Procedure for preparation of 100 mL of trypan blue solution.
The procedure is used in the direct determination of the viable cell counts of the BGM stock cultures. As trypan blue is on the U.S. EPA suspect carcinogen list, particular care should be taken in its preparation and use so as to avoid skin contact or inhalation. The wearing of rubber gloves during preparation and use is recommended.
Step a. Add 0.5 g of trypan blue to 100 mL of dH2O in a 250 mL flask. Swirl the flask until the trypan blue is completely dissolved.
Step b. Sterilize the solution by autoclaving at 121 C for 15 min and store in a screw- capped container at room temperature.
- Preparation of 100 mL of penicillin-streptomycin stock solution containing 100,000 units/mL of penicillin and 100,000 µg/mL of streptomycin.
Step a. Add 10,000,000 units of penicillin G and 10 g of streptomycin sulfate to a 250 mL flask containing 100 mL of dH2O. Mix the contents of the flasks on magnetic stirrer until the antibiotics are dissolved.
Step b. Sterilize the antibiotics by filtration through a 0.22 µm membrane filter and dis- pense in 10 mL volumes into screw-capped containers.
- Preparation of 50 mL of tetracycline stock solution.
Step a. Add 1.25 g of tetracycline hydrochloride powder and 3.75 g of ascorbic acid to a 125 mL flask containing 50 mL of dH2O. Mix the contents of the flask on a magnetic stirrer until the antibiotic is dissolved.
Step b. Sterilize the antibiotic by filtration through a 0.22 µm membrane filter and dispense in 5 mL volumes into screw-capped containers.
- Preparation of 25 mL of amphotericin B (fungizone) stock solution.
Step a. Add 0.125 g of amphotericin B to a 50 mL flask containing 25 mL of dH2O. Mix the contents of the flask on a magnetic stirrer until the antibiotic is dissolved.
VIII-34
Step b. Sterilize the antibiotic by filtration through a 0.22 µm membrane filter and dispense in 2.5 mL volumes into screw-capped containers.
PREPARATION AND PASSAGE OF BGM CELL CULTURES
A microbiological biosafety cabinet should be used to process cell cultures. If a hood is not available, cell cultures should be prepared in controlled facilities used for no other purposes. Viruses or other microorganisms must not be transported, handled, or stored in rooms used for cell culture transfer.
Vessels and Media for Cell Growth:
- The BGM cell line grows readily on the inside surfaces of glass or specially treated, tissue culture grade plastic vessels. Flat-sided, glass bottles (16 to 32 oz or equivalent growth area), 75 or 150 cm2 plastic cell culture flasks, and 690 cm2 glass or 850 cm2 plastic roller bottles are usually used for the maintenance of stock cultures. Flat-sided bottles and flasks that contain cells in a stationary position are incubated with the flat side (cell monolayer side) down. If available, roller bottles and roller apparatus units are preferable to flat-sided bottles and flasks because roller cultures require less medium than flat-sided bottles per unit of cell monolayer surface area. Roller apparatus rotation speed should be adjusted to one-half revolution per minute to ensure that cells are constantly bathed in growth medium.
- Growth and maintenance media should be prepared on the day they will be needed. Prepare growth medium by supplementing MEM/L-15 medium with 10% serum and antibiot- ics (100 mL of serum, 1 mL of penicillin-streptomycin stock, 0.5 mL of tetracycline stock and
0.2 mL of fungizone stock per 900 mL of MEM/L-15). Prepare maintenance medium by supplementing MEM/L-15 with antibiotics and 2% or 5% serum (20 or 50 mL of serum, antibiotics as above for growth medium and 80 or 50 mL of dH2O, respectively). Use maintenance media with 2% serum for CPE development.
General Procedure for Cell Passage:
Pass stock BGM cell cultures at approximately seven day intervals using growth medium.
Step 1. Pour spent medium from cell culture vessels, and discard the medium.
A gauze-covered beaker may be used to collect spent medium to prevent splatter.
Autoclave all media that have been in contact with cells or that contain serum before discard- ing.
Step 2. Add a volume of warm EDTA- trypsin reagent equal to 40% of the volume of medium that was discarded in Step 1.
See Table VIII-1 for the amount of reagents required for commonly used vessel types.
Warm the EDTA-trypsin reagent to 36.5 ± 1 C before placing it onto cell monolayers.
VIII-35
Table VIII-1. Guide for Preparation of BGM Stock Cultures |
Vessel Type |
Volume of EDTA-Trypsin (mL) |
Volume of Medium (mL)a |
Total No. Cells to Plate
per Vessel |
16 oz glass flat bottles |
10 |
25 |
2.5 ×106 |
32 oz glass flat bottles |
20 |
50 |
5.0 ×106 |
75 cm2 plastic flat flask |
12 |
30 |
3.0 ×106 |
150 cm2 plastic flat flask |
24 |
60 |
6.0 ×106 |
690 cm2 glass roller bottle |
40 |
100 |
7.0 ×106 |
850 cm2 plastic roller bottle |
48 |
120 |
8.0 ×107 |
aSerum requirements: growth medium contains 10% serum;
maintenance medium contains 2-5% serum. Antibiotic requirements: penicillin-streptomycin stock solution, 1.0 mL/liter; tetracycline stock solution, 0.5 mL/liter; fungizone stock solution, 0.2 mL/liter. |
|
|
Step 3. Allow the EDTA- trypsin reagent to remain in contact with cells at room temperature un- til the cell monolayer can be shaken loose from the inner surface of the cell culture ves- sel.
To prevent cell damage, the EDTA-trypsin reagent should remain in con- tact with the cells no longer than 5 min.
Step 4. Pour the suspended cells into centri-
fuge tubes or bottles.
To facilitate collection and resuspension of cell pellets, use tubes or bottles with conical bottoms. Centrifuge tubes and bottles used for this purpose must be able to withstand the
g-force applied.
Step 5. Centrifuge cell suspension at 1,000 ×g for 10 min to pellet cells. Pour off and discard the supernatant.
Do not exceed this speed as cells may be damaged or destroyed.
Step 6. Suspend the pelleted cells in growth medium (see Item 2 of Vessels and Media for Cell Growth) and perform a viable count on the cell suspension according to the Procedure for Performing Viable Cell Counts section below.
Resuspend pelleted cells in a sufficient volume of medium to allow thorough mixing of the cells (to reduce sampling error) and to minimize the significance of the loss of the 0.5 mL of cell suspension required for the cell counting procedure. The quantity of medium used for resuspending pelleted cells varies from 50 to several hundred milliliters, depending upon the volume of the individual laboratory’s need for cell cultures.
VIII-36
Table VIII-2. Preparation of Virus Assay Cell Cultures |
Vessel Type |
Volume of Medium* (mL) |
Final Cell Count per Vessel |
1 oz glass bottle |
4 |
9.0 ×105 |
25 cm2 plastic flask |
10 |
3.5 ×106 |
6 oz glass bottle |
15 |
5.6 ×106 |
75 cm2 plastic flask |
30 |
1.0 ×107 |
16 mm × 150 mm tubes |
2 |
4.0 ×104 |
*Serum requirements: growth medium contains 10% serum. Antibiotic requirements: penicillin- streptomycin stock solution, 1.0 mL/liter; tetracycline stock solution, 0.5 mL/liter; fungizone stock solution, 0.2 mL/liter. |
|
|
Step 7. Dilute the cell suspen- sion to the appro- priate final cell concentration with growth me- dium and dispense into cell culture vessels with a pipet, a Cornwall syringe or a Brewer- type pipetting machine dispenser.
Calculate the dilution factor requirement using the cell count and
the cell and volume parameters given in Table VIII-1 for stock cultures and in Table VIII-2
for virus assay cultures.
As a general rule, the BGM cell line should be split at a 1:2 ratio for passages 117 to 150 and a 1:3 ratio for passages 151 to 250. To plant two hundred 25 cm2 cell culture flasks weekly from cells between 151 and 250 passages would require the preparation of six roller bottles (surface area of 690 cm2 each): The contents of two to prepare the next batch of six rol- ler bottles and the contents of the other four to prepare the 25 cm2 flasks.
Step 8. Except during handling operations, maintain BGM cells at 36.5 ± 1 C in airtight cell culture vessels.
Step 9. Replace growth medium with maintenance medium containing 2% serum when cell monolayers become 95 to 100% confluent (usually three to four days after seeding with an appropriate number of cells). Replace growth medium that becomes acidic before the mono- layers become 95 to 100% confluent with maintenance medium containing 5% serum. The volume of maintenance medium should equal the volume of the discarded growth medium.
Procedure For Performing Viable Cell Counts:
Step 1. Add 0.5 mL of cell suspension (or diluted cell suspension) to 0.5 mL of 0.5% trypan blue solution in a test tube.
To obtain an accurate cell count, the optimal total number of cells per hemocytometer section should be between 20 and 50. This range is equivalent to between 6.0 × 105 and 1.5 × 106 cells per mL of cell suspension. Thus, a dilution of 1:10 (0.5 mL of cells in 4.5 mL of growth medium) is usually required for an accurate count of a cell suspension.
VIII-37
Step 2. Disperse cells by repeated pipetting.
Avoid introducing air bubbles into the suspension, because air bubbles may interfere with subsequent filling of the hemocytometer chambers.
Step 3. With a capillary pipette, carefully fill a hemocytometer chamber on one side of a slip-covered hemocytometer slide. Rest the slide on a flat surface for about 1 min to allow the trypan blue to penetrate the cell membranes of nonviable cells.
Do not under or over fill the chambers.
Step 4. Under 100X total magnification, count the cells in the four large corner sections and the center section of the hemocytometer chamber.
Include in the count cells lying on the lines marking the top and left margins of the sections, and ignore cells on the lines marking the bottom and right margins. Trypan blue is excluded by living cells. Therefore, to quantify viable cells, count only cells that are clear in color. Do not count cells that are blue.
Step 5. Calculate the average number of viable cells in each mL of cell suspension by totaling the number of viable cells counted in the five sections, multiplying this sum by 2000, and where necessary, multiplying the resulting product by the reciprocal of the dilution.
PROCEDURE FOR PRESERVATION OF BGM CELL LINE
An adequate supply of frozen BGM cells must be available to replace working cultures that are used only periodically or become contaminated or lose virus sensitivity. Cells have been held at -70 C for more than 15 years with a minimum loss in cell viability.
Preparation of Cells for Storage:
The procedure described is for the preparation of 100 cell culture vials. Cell concentra- tion must be at least 2 × 106 per mL.
The actual number of vials to be prepared should be based upon line usage and the anticipated time interval requirement between cell culture start-up and full culture production.
Step 1. Prepare cell storage medium by adding 10 mL of DMSO to 90 mL of growth medium (see Item 2 of Vessels and Media for Cell Growth ). Sterilize the resulting cell storage medium by passage through a 0.22 µm sterilizing filter.
Collect sterilized medium in a 250 mL flask containing a stir bar.
Step 2. Harvest BGM cells from cell culture vessels as directed in Steps 1 to 5 of General Procedures for Cell Passage. Count the viable cells as described above and resuspend them in the cell storage medium at a concentration of at least 2 × 106 cells per mL.
Step 3. Place the flask containing suspended cells on a magnetic stirrer and slowly mix for 30 min. Dispense 1 mL volumes of cell suspension into 2 mL capacity vials.
VIII-38
Procedure for Freezing Cells:
The freezing procedure requires slow cooling of the cells with the optimum rate of -1 C per min. A slow cooling rate can be achieved using the following method or by using the recently available freezing containers (e.g., Nalge Product No. 5100-0001) as recommended by the manufacturers.
Step 1. Place the vials in a rack and place the rack in refrigerator at 4 C for 30 min, then in a
-20 C freezer for 30 min, and finally in a -70 C freezer overnight. The transfers should be made as rapidly as possible.
To allow for more uniform cooling, wells adjoining each vial should remain empty.
Step 2. Rapidly transfer vials into boxes or other containers for long-term storage.
To prevent substantial loss of cells during storage, temperature of cells should be kept constant after -70 C has been achieved.
Procedure for Thawing Cells:
Cells must be thawed rapidly to decrease loss in cell viability.
Step 1. Place vials containing frozen cells into a 36.5 ± 1 C water bath and agitate vigorous- ly by hand until all ice has melted. Sterilize the outside surface of the vials with 0.5% I2 in 70% ethanol.
Step 2. Add BGM cells to either 6 oz tissue culture bottles or 25 cm2 tissue culture flasks containing an appropriate volume of growth medium (see Table VIII-2). Use two vials of cells for 6 oz bottles and one vial for 25 cm2 flasks.
Step 3. Incubate BGM cells at 36.5 ± 1 C. After 18 to 24 h replace the growth medium with fresh growth medium and then continue the incubation for an additional five days. Pass and maintain the new cultures as directed above.
VIII-39
PART 5 — STERILIZATION AND DISINFECTION
GENERAL GUIDELINES
- Use aseptic techniques for handling test waters, eluates and cell cultures.
- Sterilize apparatus and containers that will come into contact with test waters and all solutions that will be added to test waters unless otherwise indicated. Thoroughly clean all items before final sterilization using laboratory standard operating procedures.
- Sterilize all contaminated materials before discarding.
- Disinfect all spills and splatters.
STERILIZATION TECHNIQUES
Solutions:
- Sterilize all solutions, except those used for cleansing, standard buffers, hydrochloric acid (HCl), sodium hydroxide (NaOH), and disinfectants by autoclaving them at 121 C for at least 15 min.
The HCl and NaOH solutions and disinfectants used are self-sterilizing. When autoclav- ing buffered beef extract, use a vessel large enough to accommodate foaming.
Autoclavable Glassware, Plasticware, and Equipment:
Water speeds the transfer of heat in larger vessels during autoclaving and thereby speeds the sterilization process. Add dH2O to vessels in quantities indicated in Table VIII-3. Lay large vessels on their sides in the autoclave, if possible, to facilitate the displacement of air in the vessels by flowing steam.
- Cover the openings into autoclavable glassware, plasticware, and equipment loosely with aluminum foil before autoclaving. Autoclave at 121 C for at least 30 min.
Glassware may also be sterilized in a dry heat oven at a temperature of 170 C for at least
1 h.
- Sterilize stainless steel vessels (dispensing pressure vessel) in an autoclave at 121 C for at least 30 min.
Vent-relief valves on vessels so equipped must be open during autoclaving and closed immediately when vessels are removed from autoclave.
- Presterilize 1MDS filter cartridges and prefilter cartridges by wrapping the filters in Kraft paper and autoclaving at 121 C for 30 min.
VIII-40
Table VIII-3. Water Quantity to be Added to Vessels Before Autoclaving |
Vessel Size (liter) |
Quantity of dH2O (mL) |
2 and 3 |
25 |
4 |
50 |
8 |
100 |
24 |
500 |
54 |
1000 |
|
|
- Sterilize instruments, such as scissors and forceps, by immersing them in 95% ethanol and flaming them be- tween uses.
Chlorine Sterilization:
Sterilize pumps, plastic- ware (filter housings) and tubing that cannot withstand autoclaving, and vessels that are too large for the autoclave by chlorination.
Prefilters, but not 1MDS fil-
ters, may be presterilized with chlorine as an alternative to autoclaving. Filter apparatus modules should be disinfected by sterilization and then cleaned according to laboratory standard operating procedures before final sterilization.
- Media and Reagents
- 0.1% chlorine (HOCl) — add 19 mL of household bleach (Clorox, The Clorox Co.) to 900 mL of dH2O and adjust the pH of the solution to 6-7 with 1 M HCl. Bring to 1 liter with dH2O.
- Procedures
Ensure that the solutions come in full contact with all surfaces when performing these procedures.
- Sterilize filter apparatus modules, injector tubing and plastic bags for transporting injector tubing by recirculating or immersing the items in 0.1% chlorine for 30 min. Drain the chlorine solution from objects being sterilized. Dechlorinate using a solution containing 2.5 mL of 2% sterile sodium thiosulfate per liter of sterile dH2O.
- Thoroughly rinse pH electrodes after each use to remove particulates. Sterilize before and after each use by immersing the tip of the electrode in 0.1% chlorine for at least 1 min. Dechlorinate the electrode as in Step 2a above. Rinse with sterile dH2O.
PROCEDURE FOR VERIFYING STERILITY OF LIQUIDS
Do not add antibiotics to media or medium components until after their sterility has been demonstrated. The BGM cell line used should be checked every six months for mycoplasma contamination according to test kit instructions. Cells that are contaminated should be discarded.
VIII-41
Media and Reagents:
- Mycoplasma testing kit (Irvine Scientific Product No. T500-000). Use as directed by the manufacturer.
- Thioglycollate medium (Difco Laboratories Product No. 0257-01-9). Prepare broth medium as directed by the manufacturer.
Verifying Sterility of Small Volumes of Liquids:
Step 1. Inoculate 1 mL portions of the material to be tested for sterility into tubes containing 9 mL of thioglycollate broth by stabbing the inoculum into the broth. Incubate at 36.5 ± 1 C.
Step 2. Examine the inoculated broth daily for seven days to determine whether growth of contaminating organisms has occurred.
Containers holding the thioglycollate medium must be tightly sealed before and after the medium is inoculated.
Visual Evaluation of Media for Microbial Contaminants:
Step 1. Incubate either the entire stock of prepared media or portions taken during prepara- tion that represent at least 5% of the final volume at 36.5 ± 1 C for at least one week before use.
Step 2. Visually examine and discard any media that lose clarity.
A clouded condition that develops in the media indicates the occurrence of contaminating organisms.
CONTAMINATED MATERIALS
- Autoclave contaminated materials for at least 30 min at 121 C. Be sure that steam can enter contaminated materials freely.
- Many commercial disinfectants do not adequately kill enteric viruses. To ensure thorough disinfection, disinfect spills and other contamination on surfaces with either a solution of 0.5% iodine in 70% ethanol (5 g I2 per liter) or 0.1% chlorine. The iodine solution has the advantage of drying more rapidly on surfaces than chlorine, but may stain some surfaces.
VIII-42
PART 6 — BIBLIOGRAPHY AND SUGGESTED READING
APHA. 1995. Standard Methods for the Examination of Water and Wastewater (A. D. Eaton,
- S. Clesceri and A. E. Greenberg, ed), 19th Edition. American Public Health Association, Washington, D.C.
Barron, A. L., C. Olshevsky and M. M. Cohen. 1970. Characteristics of the BGM line of cells from African green monkey kidney. Archiv. Gesam. Virusforsch. 32:389-392.
Berg, G., R. S. Safferman, D. R. Dahling, D. Berman and C. J. Hurst. 1984. USEPA Manual of Methods for Virology. U.S. Environmental Protection Agency Publication No. EPA/600/4- 84/013, Cincinnati, OH.
Chang, S. L., G. Berg, K. A. Busch, R. E. Stevenson, N. A. Clarke and P. W. Kabler. 1958. Application of the “most probable number” method for estimating concentration of animal viruses by the tissue culture technique. Virology 6:27-42.
Crow, E. L. 1956. Confidence intervals for a proportion. Biometrika. 43:423-435.
Dahling, D. R. and B. A. Wright. 1986. Optimization of the BGM cell line culture and viral assay procedures for monitoring viruses in the environment. Appl. Environ. Microbiol.
51:790-812.
Dahling, D. R. and B. A. Wright. 1987. Comparison of the in-line injector and fluid propor- tioner used to condition water samples for virus monitoring. J. Virol. Meth. 18:67-71.
Dahling, D. R., G. Berg and D. Berman. 1974. BGM, a continuous cell line more sensitive than primary rhesus and African green kidney cells for the recovery of viruses from water. Health Lab. Sci. 11:275-282.
Dahling, D. R., R. S. Safferman and B. A. Wright. 1984. Results of a survey of BGM cell culture practices. Environ. Internat. 10:309-313.
Eagle, H. 1959. Amino acid metabolism in mammalian cell cultures. Science. 130:432-437.
EPA. 1989. Guidance manual for compliance with the filtration and disinfection requirements for public water systems using surface water sources. Office of Drinking Water, Washington, D.C.
Freshney, R. I. 1983. Culture of Animal Cells: A Manual of Basic Technique. Alan R. Liss, New York, NY.
VIII-43
Hay, R. J. 1985. ATCC Quality Control Methods for Cell Lines. American Type Culture Collection, Rockville, MD.
Hurst, C. J. 1990. Field method for concentrating viruses from water samples, pp. 285-295. In G. F. Craun (ed.), Methods for the Investigation and Prevention of Waterborne Disease Outbreaks. U.S. Environmental Protection Agency Publication No. EPA/600/1-90/005a, Washington, D.C.
Hurst, C. J. 1991. Presence of enteric viruses in freshwater and their removal by the conven- tional drinking water treatment process. Bull. W.H.O. 69:113-119.
Hurst, C. J. and T. Goyke. 1983. Reduction of interfering cytotoxicity associated with wastewater sludge concentrates assayed for indigenous enteric viruses. Appl. Environ. Microbiol. 46:133-139.
Katzenelson, E., B. Fattal and T. Hostovesky. 1976. Organic flocculation: an efficient second-step concentration method for the detection of viruses in tap water. Appl. Environ. Microbiol. 32:638-639.
Laboratory Manual in Virology. 1974. 2nd Ed. Ontario Ministry of Health, Toronto, Ontario, Canada.
Leibovitz, A. 1963. The growth and maintenance of tissue-cell cultures in free gas exchange with the atmosphere. Amer. J. Hyg. 78:173-180.
Lennette, E. H., D.A. Lennette and E.T. Lennette (ed.). 1995. Diagnostic Procedures for Viral, Rickettsial and Chlamydial Infections, 7th ed. American Public Health Association, Washington, D.C.
Malherbe, H. H. and M. Strickland-Cholmley. 1980. Viral Cytopathology. CRC Press. Boca Raton, FL.
Morris, R. and W. M. Waite. 1980. Evaluation of procedures for recovery of viruses from water—II detection systems. Water Res. 14:795-798.
Paul, J. 1975. Cell and Tissue Culture. 5th Ed. Churchill Livingstone, London, Great Britain.
Payment, P. and M. Trudel. 1985. Influence of inoculum size, incubation temperature, and cell culture density on virus detection in environmental samples. Can. J. Microbiol. 31:977- 980.
VIII-44
Rovozzo, G. C. and C. N. Burke. 1973. A Manual of Basic Virological Techniques. Prentice-Hall, Englewood Cliffs, NJ.
Sobsey, M. D. 1976. Field monitoring techniques and data analysis, pp. 87-96. In L. B. Baldwin, J. M. Davidson and J. F. Gerber (eds.), Virus Aspects of Applying Municipal Waste to Land. University of Florida, Gainesville, FL.
Sobsey, M. D. 1980. Poliovirus concentration from tap water with electropositive adsorbent filters. Appl. Environ. Microbiol. 40:201-210.
Thomas, H. A., Jr. 1942. Bacterial densities from fermentation tube tests. J. Amer. Water Works Assoc. 34:572-576.
Waymouth, C., R. G. Ham and P. J. Chapple. 1981. The Growth Requirements of Vertebrate Cells In Vitro. Cambridge University Press, Cambridge, Great Britain.
VIII-45
PART 7 — VENDORS
The vendors listed below represent one possible source for required products. Other vendors may supply the same or equivalent products.
American Type Culture Collection Continental Glass & Plastics 12301 Parklawn Dr. 841 W. Cermak Rd.
Rockville, MD 20852 Chicago, IL 60608
(800) 638-6597 (312) 666-2050
Baxter Diagnostics, Scientific Products Div. Corning: products may be ordered through 1430 Waukegan Rd. most major scientific supply houses McGaw Park, IL 60085
(800) 234-5227 Costar Corp.
7035 Commerce Circle BBL Microbiology Systems: products may Pleasanton, CA 94588 be ordered through several major scientific (800) 882-7711
supply houses
Cuno, Inc.
Becton Dickinson Microbiology Systems 400 Research Parkway 250 Schilling Circle Meriden, CT 06450
Cockeysville, MD 21030 (800)243-6894
(410) 771-0100 (Ask for a local distributor)
Curtin Matheson Scientific
Bellco Glass P.O. Box 1546
340 Edrudo Rd. Houston, TX 77251
Vineland, NJ 08360 (713) 820-9898
(800) 257-7043
DEMA Engineering Co. Brockway: products may be ordered 10014 Big Bend Blvd. through Continental Glass & Plastics Kirkwood, MO 63122
(800) 325-3362
Cincinnati Valve and Fitting Co.
3710 Southern Ave. Difco Laboratories
Cincinnati, OH 45227 P.O. Box 331058
(513) 272-1212 Detroit, MI 48232
(800) 521-0851 (Ask for a local distributor)
Cole-Parmer Instrument Co.
7425 N. Oak Park Ave. Fisher Scientific
Niles, IL 60714 711 Forbes Ave.
(800) 323-4340 Pittsburgh, PA 15219
(800) 766-7000
VIII-46
Gelman Sciences Plast-o-matic Valves, Inc.
600 S. Wagner Rd. 1384 Pompton Ave
Ann Arbor, MI 48103 Cedar Grove, NJ 07009
(800) 521-1520 (201) 256-3000 (Ask for a local distributor)
ICN Biomedicals Parker Hannifin Corp.
3300 Hyland Ave. Commercial Filters Div.
Costa Mesa, CA 92626 1515 W. South St., Lebanon, IN 46052
(800) 854-0530 (317) 482-3900
Irvine Scientific Ryan Herco
2511 Daimler Street 2509 N. Naomi St.
Santa Ana, CA 92705 Burbank, CA 91504
(800) 437-5706 (800) 848-1141
Life Technologies Sigma Chemical
P.O. Box 68 P.O. Box 14508
Grand Island, NY 14072 St. Louis, MO 63178
(800) 828-6686 (800) 325-3010
Millipore Corp. United States Plastic Corp.
397 Williams St. 1390 Neubrecht Rd.
Marlboro, MA 01752 Lima, OH 45801
(800) 225-1380 (800) 537-9724
Nalge Co. Watts Regulator
P.O. Box 20365 Box 628
Rochester, NY 14602 Lawrence, MA 01845
(716) 586-8800 (Ask for a local distributor) (508) 688-1811
Neptune Equipment Co. 520 W. Sharon Rd.
Forest Park, OH 45240 (800) 624-6975
OMEGA Engineering, Inc.
P.O. Box 4047 Stamford, CT 06907 (800) 826-6342
VIII-47
PART 8 — EXAMPLES
EXAMPLE 1
A source water sample of 211.98 L was collected at the Sampleville Water Works on 5/1/95 and shipped by overnight courier to CEPOR Laboratories. CEPOR Laboratories processed the sample on 5/2/95. After elution, the pH of the beef extract V eluate was adjusted to 7.3 with 1 M HCl. The volume of the pH-adjusted eluate, 980 mL, was recorded. Volumes of 34.3 mL (980 × 0.035) and 98.0 mL (980 × 0.1) were removed for the Coliphage Assay (Section IX) and for archiving, respectively. An Adjusted Total Sample Volume (ATSV) was then calculated by multiplying 211.98 L × 0.865. An ATSV of 183 L was recorded on the Virus Data Sheet.
The sample was immediately processed by the Organic Flocculation Concentration Procedure. Following centrifugation at 4,000 ×g, the supernatant was adjusted to pH 7.3 and passed through a sterilizing filter. A Final Concentrated Sample Volume (FCSV) of 28.0 mL was obtained.
The Assay Sample Volume was calculated using the formula:
ASSAY SAMPLE VOLUME (S) D
ATSV
× FCSV
where D is the Volume of Original Water Sample Assayed (i.e., 100 L for source water or 1000 L for finished water). Thus the Assay Sample Volume for Sampleville-01 is:
S 100 liters 183 liters
× 28.0 ml 15.3 ml
The 15.3 mL is the volume of the Final Concentrated Sample that must be inoculated onto tissue culture and that represents 100 L of the source water.
Two subsamples were prepared from the Final Concentrated Sample. Subsample 1 was prepared by placing 0.55 × 15.3 mL = 8.4 mL into a separate container. Subsample 2 was prepared by placing 0.67 × 15.3 mL = 10.2 mL into a third container. Although only 0.5
× 15.3 = 7.65 mL (representing 50 L of source water) must be inoculated onto tissue culture flasks for each subsample, the factor “0.55″ was used for subsample 1 to account for unrecov- erable losses associated with removing a subsample from its container. The factor “0.67″ was used for subsample 2 to account for losses associated with the container and to provide additional sample for the preparation of dilutions, if required.
VIII-48
Subsample 2 and the remaining portions of the Final Concentrated Sample were frozen at -70 C.
The inoculation volume was calculated to be 15.3 mL ÷ 20 = 0.76 mL per flask. To make the inoculation procedure more convenient, it was decided to dilute subsample 1 so that
1.0 mL of inoculum contained an amount of subsample 1 equal to the inoculum volume. To
do this, 10.5 × (1.00 – 0.76) = 2.52 mL of 0.15 M Na2HPO4 7H2O, pH 7.3, was added to 10.5
× 0.76 = 7.98 mL of subsample 1. One milliliter of diluted subsample 1 was then inoculated
onto each of ten 25 cm2 flasks of BGM cells at passage 123. A negative control was prepared
by inoculating a flask with 1.0 mL of 0.15 M Na2HPO4 7H2O, pH 7.3. A positive control
was prepared by inoculating a flask with 1.0 mL of 0.15 M Na2HPO4 7H2O, pH 7.3 contain-
ing 200 PFU/mL of attenuated poliovirus type 3. Following adsorption, 9.0 mL of mainte-
nance medium was added and the cultures were incubated at 36.5 C. These cultures and those described below were observed for CPE as described in the protocol and positive cultures were frozen when 75% of a flask showed signs of CPE.
On May 9th five flasks inoculated with subsample 1 and the positive control showed signs of CPE. Because fewer than eight flasks inoculated with subsample 1 showed CPE, 10 additional 25 cm2 flasks of BGM cells at passage 124 were inoculated with 1.0 mL each of subsample 2 diluted in the same manner as subsample 1. Another negative control and positive control were also prepared and inoculated.
By May 16th a total of seven flasks inoculated with subsample 1 showed signs of CPE. The flasks that had not been previously frozen were now frozen at -70 C and then all flasks were thawed. Several milliliters of fluid from each of the eight positive flasks (seven samples plus the positive control) were passed through a sterilizing filter. Twelve flasks of BGM cells at passage 125 were inoculated with one milliliter of the supernatant from either negative cultures or from filtered positive cultures.
By May 23rd a total of five flasks from subsample 2 showed signs of CPE. All flasks were frozen, thawed and then passaged as described for subsample 1 using BGM cells at passage 126.
By May 30th only six flasks from the second passage of subsample 1 and the positive control showed CPE. Thus one culture from the 1st passage failed to confirm in the second pass and a value of 6 was recorded in the Number of Replicates with CPE column of the Total Culturable Virus Data Sheet . The flasks were then discarded.
On June 6th seven flasks (the five original plus two new flasks) from the second passage of subsample 2 demonstrated CPE. The two new flasks and controls were frozen at -70 C, thawed and passaged a third time as described above using BGM cells at passage 127.
All other flasks were discarded.
VIII-49
By June 12 the positive control and the two third passage flasks had developed CPE. All flasks were discarded at this time (the flasks would have been examined until 6/20 if at least one had remained negative). A value of 7 was recorded into the Number of Replicates with CPE column of the Total Culturable Virus Data Sheet .
The MPN software program supplied by the U.S. EPA was used to calculate the MPN/mL and 95% confidence limit values. “I. SIZE OF INOCULUM VOLUME (mL)” on the main screen was changed from 1 to 0.76. “A. PROCEED WITH DATA INPUT” was pressed followed by “ENTER” to overwrite the existing output file. Alternatively, “NO” could have been entered and the output file renamed. The number of positive replicates, “13,” was then entered. Following the calculation by the program, the MPN and 95% Confidence Limit values were recorded onto the Quantitation of Total Culturable Virus Data Sheet .
The program was exited by pressing “I. EXIT THE PROGRAM.”
The MPN per 100 liter value (Ml) was calculated according to the formula:
M 100 MmS
l D
100 × 1.38 × 15.3 21.1
100
where Mm is the MPN value per milliliter from the Quantitation of Total Culturable Virus Data Sheet, S is the Assay Sample Volume and D is the Volume of Original Water Sample Assayed (S and D are obtained from the Virus Data Sheet).
The Lower 95% Confidence Limit per 100 liter (CLl) was calculated according to the formula:
CLl
100 CLlmS D
100 × 0.70 × 15.3 10.7
100
where CLlm is the lower 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet.
The Upper 95% Confidence Limit per 100 liter (CLu) was calculated according to the formula:
CLu
100 CLumS D
100 × 2.27 × 15.3 34.7
100
VIII-50
where CLum is the upper 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet.
VIII-51
SAMPLE DATA SHEET |
SAMPLE NUMBER: Sampleville-01 |
UTILITY NAME: Sampleville Water Works |
UTILITY ADDRESS: 1 Water Street
CITY: Sampleville STATE: OH ZIP: 45999 |
SAMPLER’S NAME: Mr. Brian Hall |
WATER TEMPERATURE: 23.5 C TURBIDITY: 3.6 NTU |
WATER pH: 7.8 |
ADJUSTED WATER pH: NA |
THIOSULFATE ADDED: (CHECK) YES X NO |
INIT. METER READING: 6048.10 CHECK UNITS: X gallons ft3
date: 5/1/95 time: 9 am |
FINAL METER READING: 6104.10 CHECK UNITS: X gallons ft3
date: 5/1/95 time: 9:30 am |
TOTAL SAMPLE VOLUME: 211.98 L
(Final-Initial meter readings × 3.7854 (for readings in gallons) or × 28.316 (for readings in ft3)) |
SHIPMENT DATE: 5/1/95 |
CONDITION ON ARRIVAL: Cold/Not frozen |
COMMENTS: |
VIII-52
VIRUS DATA SHEET |
SAMPLE NUMBER: SAMPLEVILLE-01 |
ANALYTICAL LABORATORY NAME: CEPOR LABORATORIES |
ANALYTICAL LABORATORY ADDRESS: 42 RUECKERT ST.
CITY: CINCINNATI STATE: OH ZIP: 45219 |
ADJUSTED TOTAL SAMPLE VOLUME (ATSV): 1 183 L |
DATE ELUTED: 5/2/95 |
TIME: 10 am |
ELUATE VOLUME RECOVERED: 980 mL |
VOLUME OF ELUATE ARCHIVED: 98.0 mL |
DATE CONCENTRATED: 5/2/95 |
TIME: 1 pm |
FINAL CONCENTRATED SAMPLE VOLUME (FCSV): 28.0 mL |
ASSAY SAMPLE VOLUME (S): 15.3 mL |
VOLUME OF ORIGINAL WATER SAMPLE
ASSAYED (D): 100 L2 |
INOCULUM VOLUME: 0.76 mL |
DATES ASSAYED 3rd Passage
BY CPE: 1st Passage 2nd Passage (If necessary) |
Subsample 1: |
5/2/95 |
5/16/95 |
|
Subsample 2: |
5/9/95 |
5/23/95 |
6/6/95 |
MPN/100 L3: 21 |
95% CONFIDENCE LIMITS
LOWER: 11 UPPER: 35 |
COMMENTS: |
ANALYST: B.G. Moore |
1Enter the Total Sample Volume times 0.965 if a coliphage sample is taken, times 0.9 if archiving is required, times 0.865 if a coliphage sample is taken and archiving is required or times 1 if a coliphage sample is not taken and archiving is not required.
2Must be at least 100 L for source water and 1000 L for finished water.
3Value calculated from the Quantitation of Total Culturable Virus form as described in the Virus Quantitation section of Part 3. |
VIII-53
TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE #: Sampleville-01 |
|
Total Number of Replicates |
|
Subsample 1 |
Subsample 2 |
Sample |
Inoculated |
Without CPE |
With CPE |
Inoculated |
Without CPE |
With CPE |
1st Passage Neg. Cont. |
1 |
1 |
0 |
1 |
1 |
0 |
Pos. Cont. |
1 |
0 |
1 |
1 |
0 |
1 |
Undiluted |
10 |
3 |
7 |
10 |
5 |
5 |
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
2nd Passage1
Neg. Cont. |
1 |
1 |
0 |
1 |
1 |
0 |
Pos. Cont. |
1 |
0 |
1 |
1 |
0 |
1 |
Undiluted |
10 |
4 |
6 |
10 |
3 |
7 |
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
3rd Passage2
Neg. Cont. |
|
|
|
1 |
1 |
0 |
Pos. Cont. |
|
|
|
1 |
0 |
1 |
Undiluted |
|
|
|
2 |
0 |
2 |
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
1A portion of medium from each 1st passage vessel, including controls, must be repas- saged for conformation. The terms “Undiluted,” “1:5 Dilution” and “1:25 Dilution” under the 2nd and 3rd Passage headings refer to the original sample dilutions for the 1st passage. If higher dilutions are used, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column.
2Samples that were negative on the first passage and positive on the 2nd passage must be passaged a third time for conformation. If a third passage is required, all controls must be passaged again. |
VIII-54
QUANTITATION OF TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE NUMBER: Sampleville-01 |
Sample |
Number Replicates inoculated |
Number with CPE |
MPN/mL1 |
95% Confidence Limits |
Lower |
Upper |
Undiluted Samples |
1.38 |
0.70 |
2.27 |
Subsample 1 |
10 |
6 |
Subsample 2 |
10 |
7 |
Total Undiluted |
20 |
13 |
Subsample 2 results (Dilutions Required) |
Undiluted |
|
|
1:5 Dilution |
|
|
1:25 Dilution |
|
|
1Use the values recorded in the Total Undiluted row to calculate the MPN/mL result and confidence limits when dilutions are not required. If dilutions are required, base the calculation upon the values recorded in the Undiluted, 1:5 Diluted and 1:25 Diluted rows for subsample 2. If higher dilutions are used for subsample 2, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column. The MPN/mL and 95% Confidence Limit values must be obtained using the computer program supplied by the U.S. EPA. |
VIII-55
EXAMPLE 2
A source water sample of 200.63 L was collected at the Sampleville Water Works on 6/5/95 and shipped by overnight courier to CEPOR Laboratories. CEPOR Laboratories processed the sample on 6/6/95. After elution, the pH was adjusted to 7.3. A volume of 985 mL of pH-adjusted eluate was obtained and 34.5 mL (985 mL × 0.035) was removed for the Coliphage Assay (Section IX). Archiving was not required. An Adjusted Total Sample Volume of 194 L (200.63 L × 0.965) was recorded on the Virus Data Sheet.
The sample was immediately processed by the Organic Flocculation Concentration Procedure. Following centrifugation at 4,000 ×g, the supernatant was adjusted to pH 7.3 and passed through a sterilizing filter. A Final Concentrated Sample Volume of 32.0 mL was obtained, giving an Assay Sample Volume for Sampleville-02 of:
S 100 liters
194 liters
× 32.0 ml 16.5 ml
Subsample 1 was prepared by placing 0.55 × 16.5 mL = 9.1 mL into a separate container. Subsample 2 was prepared by placing 0.67 × 16.5 mL = 11.1 mL into a third container. Subsample 2 and the remaining portions of the Final Concentrated Sample were frozen at -70 C.
Subsample 1 was inoculated onto each of ten 25 cm2 flasks of BGM cells at passage 127 using an inoculation volume of 16.5 mL ÷ 20 = 0.82 mL per flask. A negative control
was prepared by inoculating a flask with 0.82 mL of 0.15 M Na2HPO4 7H2O, pH 7.3. A
positive control was prepared by inoculating a flask with 0.82 mL of 0.15 M Na2HPO4
7H2O, pH 7.3 containing 241.0 PFU/mL (200.0 PFU/0.82 mL) of attenuated poliovirus type 3. Following adsorption, 9.18 mL of maintenance medium was added and the cultures were incubated at 36.5 C.
On June 13 nine flasks inoculated with subsample 1 and the positive control showed signs of CPE. After thawing subsample 2, a 1:5 dilution was prepared by mixing 0.1334 ×
16.5 = 2.20 mL of subsample 2 with 0.5334 × 16.5 = 8.80 mL of 0.15 M Na2HPO4 7H2O,
pH 7.3. A 1:25 dilution was prepared by mixing 2.20 mL of the 1:5 dilutions with 8.80 mL of
0.15 M Na2HPO4 7H2O, pH 7.3. Ten 25 cm flasks of BGM cells at passage 128 were then
inoculated with 0.82 mL each of undiluted subsample 2. Ten flasks were inoculated with
0.82 mL each of subsample 2 diluted 1:5 and ten flasks were inoculated with 0.82 mL each of subsample 2 diluted 1:25. Another negative control and positive control were also prepared and inoculated.
By June 20 all 10 flasks inoculated with subsample 1 showed signs of CPE and were repassaged as described in example 1.
VIII-56
By June 27 all 10 flasks inoculated with undiluted subsample 2 had developed CPE. Eight flasks inoculated with the 1:5 dilution of subsample 2 and four flasks inoculated with the 1:25 dilution of subsample 2 demonstrated CPE. All flasks were re-passaged as described for example 1.
By July 5th all 10 flasks from the second passage of subsample 1 were confirmed as positive and were discarded.
By July 11th all 10 flasks inoculated with the second passage of undiluted subsample 2 had developed CPE. The eight positive flasks from the 1st passage of the 1:5 dilution of subsample 2 were positive in the second passage. Three flasks inoculated with the second passage of the 1:25 dilution of subsample 2 remained positive.
The MPN software program supplied by the U.S. EPA was used to calculate the MPN/mL and 95% confidence limit values. After the main screen appeared, “G. NUMBER OF DILUTIONS” was changed from 1 to 3. “H. NUMBER OF REPLICATES PER DILU-
TION” was changed from 20 to 10 and “I. SIZE OF INOCULUM VOLUME (mL)” was changed from 1 to 0.82. “A. PROCEED WITH DATA INPUT” was pressed followed by “ENTER” to overwrite the existing output file. The number of positive replicates per dilution, “10, 8, and 3” was entered with the values separated by spaces. Following program calcula- tions, the MPN/mL and 95% Confidence Limit values/mL were recorded onto the Quantitation of Total Culturable Virus Data Sheet . The program was exited by pressing “I. EXIT THE PROGRAM.”
The MPN per 100 liter value (Ml) was calculated according to the formula:
M 100 MmS
l D
100 × 10.15 × 16.5 167
100
where Mm is the MPN value per milliliter from the Quantitation of Total Culturable Virus Data Sheet, S is the Assay Sample Volume and D is the Volume of Original Water Sample Assayed (S and D are obtained from the Virus Data Sheet).
The Lower 95% Confidence Limit per 100 liter (CLl) was calculated according to the formula:
CLl
100 CLlmS D
100 × 5.04 × 16.5 83.1
100
where CLlm is the lower 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet.
VIII-57
The Upper 95% Confidence Limit per 100 liter (CLu) was calculated according to the formula:
CLu
100 CLumS D
100 × 18.25 × 16.5 301
100
where CLum is the upper 95% confidence limit per milliliter from the Quantitation of Total Culturable Virus Data Sheet.
VIII-58
SAMPLE DATA SHEET |
SAMPLE NUMBER: Sampleville-02 |
UTILITY NAME: Sampleville Water Works |
UTILITY ADDRESS: 1 Water Street
CITY: Sampleville STATE: OH ZIP: 45999 |
SAMPLER’S NAME: Mr. Brian Hall |
WATER TEMPERATURE: 26.5 C TURBIDITY: 2.3 NTU |
WATER pH: 7.7 |
ADJUSTED WATER pH: NA |
THIOSULFATE ADDED: (CHECK) YES X NO |
INIT. METER READING: 6129.3 CHECK UNITS: X gallons ft3
date: 6/5/95 time: 8:30 am |
FINAL METER READING: 6182.3 CHECK UNITS: X gallons ft3
date: 6/5/95 time: 9:00 am |
TOTAL SAMPLE VOLUME: 200.63 L
(Final-Initial meter readings × 3.7854 (for readings in gallons) or × 28.316 (for readings in ft3)) |
SHIPMENT DATE: 6/5/95 |
CONDITION ON ARRIVAL: Cold/Not frozen |
COMMENTS: |
VIII-59
VIRUS DATA SHEET |
SAMPLE NUMBER: SAMPLEVILLE-02 |
ANALYTICAL LABORATORY NAME: CEPOR LABORATORIES |
ANALYTICAL LABORATORY ADDRESS: 42 RUECKERT ST.
CITY: CINCINNATI STATE: OH ZIP: 45219 |
ADJUSTED TOTAL SAMPLE VOLUME (ATSV): 1 194 L |
DATE ELUTED: 6/6/95 |
TIME: 9:50 am |
ELUATE VOLUME RECOVERED: 985 mL |
VOLUME OF ELUATE ARCHIVED: 0 mL |
DATE CONCENTRATED: 6/6/95 |
TIME: 1 pm |
FINAL CONCENTRATED SAMPLE VOLUME (FCSV): 32.0 mL |
ASSAY SAMPLE VOLUME (S): 16.5 mL |
VOLUME OF ORIGINAL WATER SAMPLE
ASSAYED (D): 100 L2 |
INOCULUM VOLUME: 0.82 mL |
DATES ASSAYED BY 3rd Passage
CPE: 1st Passage 2nd Passage (If necessary) |
Subsample 1: |
6/6/95 |
6/20/95 |
|
Subsample 2: |
6/13/95 |
6/27/95 |
|
MPN/100 L3: 167 |
95% CONFIDENCE LIMITS
LOWER: 83 UPPER: 301 |
COMMENTS: |
ANALYST: B.G. Moore |
1Enter the Total Sample Volume times 0.965 if a coliphage sample is taken, times 0.9 if archiving is required, times 0.865 if a coliphage sample is taken and archiving is required or times 1 if a coliphage sample is not taken and archiving is not required.
2Must be at least 100 L for source water and 1000 L for finished water.
3Value calculated from the Quantitation of Total Culturable Virus form as described in the Virus Quantitation section of Part 3. |
VIII-60
TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE #: Sampleville-02 |
|
Total Number of Replicates |
|
Subsample 1 |
Subsample 2 |
Sample |
Inoculated |
Without CPE |
With CPE |
Inoculated |
Without CPE |
With CPE |
1st Passage Neg. Cont. |
1 |
1 |
0 |
1 |
1 |
0 |
Pos. Cont. |
1 |
0 |
1 |
1 |
0 |
1 |
Undiluted |
10 |
0 |
10 |
10 |
0 |
10 |
1:5 Dil. |
|
|
|
10 |
2 |
8 |
1:25 Dil. |
|
|
|
10 |
6 |
4 |
2nd Passage1
Neg. Cont. |
1 |
1 |
0 |
1 |
1 |
0 |
Pos. Cont. |
1 |
0 |
1 |
1 |
0 |
1 |
Undiluted |
10 |
0 |
10 |
10 |
0 |
10 |
1:5 Dil. |
|
|
|
10 |
2 |
8 |
1:25 Dil. |
|
|
|
10 |
7 |
3 |
3rd Passage2
Neg. Cont. |
|
|
|
|
|
|
Pos. Cont. |
|
|
|
|
|
|
Undiluted |
|
|
|
|
|
|
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
1A portion of medium from each 1st passage vessel, including controls, must be repas- saged for conformation. The terms “Undiluted,” “1:5 Dilution” and “1:25 Dilution” under the 2nd and 3rd Passage headings refer to the original sample dilutions for the 1st passage. If higher dilutions are used, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column.
2Samples that were negative on the first passage and positive on the 2nd passage must be passaged a third time for conformation. If a third passage is required, all controls must be passaged again. |
VIII-61
QUANTITATION OF TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE NUMBER: Sampleville-02 |
Sample |
Number Replicates inoculated |
Number with CPE |
MPN/mL1 |
95% Confidence Limits |
Lower |
Upper |
Undiluted Samples |
10.15 |
5.04 |
18.25 |
Subsample 1 |
10 |
10 |
Subsample 2 |
|
|
Total Undiluted |
NA |
NA |
Subsample 2 results (Dilutions Required) |
Undiluted |
10 |
10 |
1:5 Dilution |
10 |
8 |
1:25 Dilution |
10 |
3 |
1Use the values recorded in the Total Undiluted row to calculate the MPN/mL result and confidence limits when dilutions are not required. If dilutions are required, base the calculation upon the values recorded in the Undiluted, 1:5 Diluted and 1:25 Diluted rows for subsample 2. If higher dilutions are used for subsample 2, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column. The MPN/mL and 95% Confidence Limit values must be obtained using the computer program supplied by the U.S. EPA. |
VIII-62
PART 9 — DATA SHEETS 7
7Copies of all Data Sheets are available upon request in WordPerfect for Windows, version 6.1 format. Send requests to the ICR Laboratory Coordinator, USEPA, TSD, 26
- Martin Luther King Drive, Cincinnati, OH 45268.
VIII-63
SAMPLE DATA SHEET |
SAMPLE NUMBER: |
UTILITY NAME: |
UTILITY ADDRESS: CITY: |
STATE: ZIP: |
|
SAMPLER’S NAME: |
WATER TEMPERATURE: |
C TURBIDITY: |
NTU |
WATER pH: |
ADJUSTED WATER pH: |
THIOSULFATE ADDED: |
(CHECK) YES NO |
|
INIT. METER READING:
date: |
CHECK UNITS: gallons time: |
ft3 |
FINAL METER READING:
date: |
CHECK UNITS: gallons time: |
ft3 |
TOTAL SAMPLE VOLUME: L
(Final-Initial meter readings × 3.7854 (for readings in gallons) or × 28.316 (for readings in ft3)) |
SHIPMENT DATE: |
CONDITION ON ARRIVAL: |
COMMENTS: |
VIII-64
VIRUS DATA SHEET |
SAMPLE NUMBER: |
ANALYTICAL LABORATORY NAME: |
ANALYTICAL LABORATORY ADDRESS: CITY: STATE: |
ZIP: |
ADJUSTED TOTAL SAMPLE VOLUME (ATSV): 1 |
L |
DATE ELUTED: |
TIME: |
ELUATE VOLUME RECOVERED: |
mL |
VOLUME OF ELUATE ARCHIVED: |
mL |
DATE CONCENTRATED: |
TIME: |
FINAL CONCENTRATED SAMPLE VOLUME (FCSV): |
mL |
ASSAY SAMPLE VOLUME (S): |
mL |
VOLUME OF ORIGINAL WATER SAMPLE ASSAYED (D): |
L |
INOCULUM VOLUME: |
mL |
DATES ASSAYED
BY CPE: 1st Passage 2nd Passage |
3rd Passage (If necessary) |
Subsample 1: |
|
|
|
Subsample 2: |
|
|
|
MPN/100 L3: |
95% CONFIDENCE LIMITS
LOWER: UPPER: |
COMMENTS: |
ANALYST: |
1Enter the Total Sample Volume times 0.965 if a coliphage sample is taken, times 0.9 if archiving is required, times 0.865 if a coliphage sample is taken and archiving is required or times 1 if a coliphage sample is not taken and archiving is not required.
2Must be at least 100 L for source water and 1000 L for finished water.
3Value calculated from the Quantitation of Total Culturable Virus form as described in the Virus Quantitation section of Part 3. |
VIII-65
TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE #: |
|
Total Number of Replicates |
|
Subsample 1 |
Subsample 2 |
Sample |
Inoculated |
Without CPE |
With CPE |
Inoculated |
Without CPE |
With CPE |
1st Passage Neg. Cont. |
|
|
|
|
|
|
Pos. Cont. |
|
|
|
|
|
|
Undiluted |
|
|
|
|
|
|
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
2nd Passage1
Neg. Cont. |
|
|
|
|
|
|
Pos. Cont. |
|
|
|
|
|
|
Undiluted |
|
|
|
|
|
|
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
3rd Passage2
Neg. Cont. |
|
|
|
|
|
|
Pos. Cont. |
|
|
|
|
|
|
Undiluted |
|
|
|
|
|
|
1:5 Dil. |
|
|
|
|
|
|
1:25 Dil. |
|
|
|
|
|
|
1A portion of medium from each 1st passage vessel, including controls, must be re- passaged for conformation. The terms “Undiluted,” “1:5 Dilution” and “1:25 Dilution” under the 2nd and 3rd Passage headings refer to the original sample dilutions for the 1st passage. If higher dilutions are used, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column.
2Samples that were negative on the first passage and positive on the 2nd passage must be passaged a third time for conformation. If a third passage is required, all controls must be passaged again. |
VIII-66
QUANTITATION OF TOTAL CULTURABLE VIRUS DATA SHEET |
SAMPLE NUMBER: |
Sample |
Number Replicates inoculated |
Number with CPE |
MPN/mL1 |
95% Confidence Limits |
Lower |
Upper |
Undiluted Samples |
|
|
|
Subsample 1 |
|
|
Subsample 2 |
|
|
Total Undiluted |
|
|
Subsample 2 results (Dilutions Required) |
Undiluted |
|
|
1:5 Dilution |
|
|
1:25 Dilution |
|
|
1Use the values recorded in the Total Undiluted row to calculate the MPN/mL result and confidence limits when dilutions are not required. If dilutions are required, base the calculation upon the values recorded in the Undiluted, 1:5 Diluted and 1:25 Diluted rows for subsample 2. If higher dilutions are used for subsample 2, record the data from the three highest dilutions showing positive results and place the actual dilution amount in the sample column. The MPN/mL and 95% Confidence Limit values must be obtained using the computer program supplied by the U.S. EPA. |
VIII-67
SECTION IX. COLIPHAGE ASSAY
This Section outlines the procedures for coliphage detection by plaque assay. It should be noted that the samples to be analyzed may contain pathogenic human enteric viruses.
Laboratories performing the coliphage analysis are responsible for establishing an adequate safety plan.
ASSAY COMPONENTS
Apparatus and Materials:
- Sterilizing filter — 0.45 µm (Nuclepore Product No. 140667 or equivalent).
Always pass about 10 mL of 1.5% beef extract through the filter just prior to use to minimize phage adsorption to the filter.
- Water bath set at 44.5 ± 1 C.
- Incubator set at 36.5 ± 1 C.
Media and Reagents:
The amount of media prepared may be increased proportionally to the number of samples to be analyzed.
- Saline-calcium solution — dissolve 8.5 g of NaCl and 0.22 g of CaCl2 in a total of 1 L of dH2O. Dispense in 9 mL aliquots in 16 × 150 mm screw-capped test tubes (Baxter Product No. T1356-6A or equivalent) and sterilize by autoclaving at 121 C for 15 min.
- Tryptone agar slants — add 1.0 g tryptone (Difco Product No. 0123 or equivalent), 0.1 g yeast extract (Difco Product No. 0127 or equivalent), 0.1 g glucose, 0.8 g NaCl, 0.022 g CaCl2, and 1.2 g of Bacto-agar (Difco Product No. 0140 or equivalent) to a total volume of 100 mL of dH2O in a 250 mL flask. Dissolve by autoclaving at 121 C for 20 min and dispense 8 mL aliquots into 16 × 150 mm test tubes with tube closures (Baxter Product Nos. T1311-16XX and T1291-16 or equivalent). Prepare slants by allowing the agar to solidify with the tubes at about a 20 angle. Slants may be stored at 4 C for up to two months.
- Tryptone bottom agar — Prepare one day prior to sample analysis using the ingredients and concentrations listed for tryptone agar slants, except use 1.5 g of Bacto-agar. After autoclaving, pipet 15 mL aliquots aseptically into sterile 100 × 15 mm petri plates and allow the agar to harden. Store the plates at 4 C overnight and warm to room temperature for 1 h before use.
IX-1
- Tryptone top agar — Prepare the day of sample analysis using the ingredients and concentrations listed for tryptone agar slants, except use 0.7 g of Bacto-agar. Autoclave and place in the 44.5 ± 1 C water bath.
- Tryptone broth — Prepare on the day prior to sample analysis as for tryptone agar slants, except without agar.
- Beef extract V powder (BBL Microbiology Systems Product No. 97531) — prepare buffered 1.5% beef extract by dissolving 1.5 g of beef extract powder and 0.375 g of glycine (final glycine concentration = 0.05 M) in 90 mL of dH2O. Adjust the pH to 7.0 – 7.5, if necessary, and bring the final volume to 100 mL with dH2O. Autoclave at 121 C for 15 min and use at room temperature.
Beef extract solutions may be stored for one week at 4 C or for longer periods at -20 C.
SAMPLE PROCESSING
Step 1. To measure the concentration of coliphage in water samples, use the coliphage sample prepared from the pH-adjusted 1MDS eluate as described in the Elution Procedure in Part 2 of Section VII. Virus Monitoring Protocol .
Step 2. Filter the coliphage sample through a 0.45 µm sterilizing filter.
Step 3. Assay ten 1 mL volumes each for somatic and male-specific coliphage within 24 h. Store the remaining eluate at 4 C to serve as a reserve in the event of sample contamination or high coliphage densities. If the coliphage density is expected or demonstrated to be greater than 100 PFU/mL, dilute the original or remaining eluate with a serial 1:10 dilution series into saline-calcium solutions. Assay the dilutions which will result in plaque counts of 100 or less.
SOMATIC COLIPHAGE ASSAY
Storage of E. coli C Host Culture for Somatic Coliphage Assay:
- For short term storage inoculate a Escherichia coli C (American Type Culture Collection Product No. 13706) host culture onto tryptone agar slants with a sterile inoculating loop by spreading the inoculum evenly over entire slant surface. Incubate the culture overnight at 36.5
± 1 C. Store at 4 C for up to two weeks.
- For long term storage inoculate a 5-10 mL tube of tryptone broth with the host culture. Incubate the broth culture overnight at 36.5 ± 1 C. Add 1/10th volume of sterile glycerol. Dispense into 1 mL aliquots in cryovials (Baxter Product No. T4050-8 or equivalent) and store at -70 C.
IX-2
Preparation of Host for Somatic Coliphage Assay:
Step 1. Inoculate 5 mL of tryptone broth with E. coli C from a slant with an inoculating loop and incubate for 16 h at 36.5 ± 1 C.
Step 2. Transfer 1.5 mL of the 16 h culture to 30 mL of tryptone broth in a 125 mL flask and incubate for 4 h at 36.5 ± 1 C with gentle shaking. The amount of inoculum and broth used in this step can be proportionally altered according to need.
Preparation of X174 Positive Control:
Step 1. Rehydrate a stock culture of X174 (American Type Culture Collection Product No. 13706-B1) and store at 4 C.
Step 2. Prepare a 30 mL culture of E. coli C as described in section titled Preparation of Host for Somatic Coliphage Assay. Incubate for 2 h at 36.5 ± 1 C with shaking. Add 1 mL of rehydrated phage stock and incubate for an additional 4 h at 36.5 ± 1 C.
Step 3. Filter the culture through a 0.45 µm sterilizing filter.
Step 4. Prepare 10-7, 10-8 and 10-9 dilutions of the filtrate using saline-calcium solution tubes.
These dilutions should be sufficient for most X174 stocks. Some stocks may require higher or lower dilutions.
Step 5. Add 1 mL of the 10-9 dilution into each of five 16 × 150 mm test tubes. Using the same pipette, add 1 mL of the 10-8 dilution into each of five additional tubes and then 1 mL of the 10-7 dilution into five tubes. Label the tubes with the appropriate dilution.
Step 6. Add 0.1 mL of the host culture into each of the 15 test tubes from Step 5.
Step 7. Add 3 mL of the melted tryptone top agar held in the 44.5 ± 1 C water bath to one test tube at a time. Mix and immediately pour the contents of the tube over the bottom agar of a petri dish labeled with sample identification information. Rotate the dish to spread the suspension evenly over the surface of the bottom agar and place it onto a level surface to allow the agar to solidify.
Step 8. Incubate the inoculated plates at 36.5 ± 1 C overnight and examine for plaques the following day.
Step 9. Count the number of plaques on each of the 15 plates (don’t count plates giving plaque counts significantly more than 100). The five plates from one of the dilutions should
IX-3
give plaque counts of about 20 to 100 plaques. Average the plaque counts on these five plates and multiply the result by the reciprocal of the dilution to obtain the titer of the undiluted stock.
Step 10. Dilute the filtrate to 30 to 80 PFU/mL in tryptone broth for use in a positive control in the coliphage assay. Store the original filtrate and the diluted positive control at 4 C.
Before using the positive control for the 1st time, place 1 mL each into ten 16 × 150 mm test tubes and assay using Steps 6-8. Count the plaques on all plates and divide by 10. If the result is not 30 to 80, adjust the dilution of the positive control sample and assay again.
Procedure for Somatic Coliphage Assay:
Step 1. Sample preparation:
- Add 1 mL of the water eluate sample to be tested to each of ten 16 × 150 mm test tubes.
- Add 1 mL of buffered 1.5% beef extract to a 16 × 150 mm test tube for a negative control.
- Add 1 mL of the diluted X174 positive control to another 16 × 150 mm test tube.
Step 2. Add 0.1 mL of the host culture to each test tube containing eluate or positive control.
Step 3. Add 3 mL of the melted tryptone top agar held in the 44.5 ± 1 C water bath to one test tube at a time. Mix and immediately pour the contents of the tube over the bottom agar of a petri dish labeled with sample identification information. Tilt and rotate the dish to spread the suspension evenly over the surface of the bottom agar and place it onto a level surface to allow the agar to solidify.
Step 4. Incubate the inoculated plates at 36.5 ± 1 C overnight and examine for plaques the following day.
Step 5. Count the total number of plaques on the ten plates receiving the water eluate. Step 6. Somatic coliphage enumeration.
IX-4
- Calculate the somatic coliphage titer (Vs) in PFU per 100 L according to the formula:
V 100 × P × D × E
S I × C
where P is the total number of plaques from Step 5, D is the reciprocal of the dilution made on the inoculum before plating (D = 1 for undiluted samples) and E is the total vol- ume of eluate recovered (from the Virus Data Sheet of the Total Culturable Virus Proto- col). I is the total volume (in mL) of the eluate sample assayed on the ten plates. C is the amount of water sample filtered in liters (from the Sample Data Sheet of the Total Cultur- able Virus Protocol). Record the value of VS in the ICR database.
- Count the plaques on the positive control plate. Maintain a record of the plaque count as a check on the virus sensitivity of the E. coli C host. Assay any water eluate samples again where the positive control counts are more than one log below their normal average.
MALE-SPECIFIC COLIPHAGE ASSAY
Storage of E. coli Famp Host Culture for Male-Specific Coliphage Assay: 1
- For short term storage inoculate a Escherichia coli Famp host culture onto tryptone agar slants with a sterile inoculating loop by spreading the inoculum evenly over entire slant surface. Incubate the culture overnight at 36.5 ± 1 C. Store at 4 C for up to two weeks.
- For long term storage inoculate a 5-10 mL tube of tryptone broth with the host culture. Incubate the broth culture overnight at 36.5 ± 1 C. Add 1/10th volume of sterile glycerol. Dispense into 1 mL aliquots in cryovials (Baxter Product No. T4050-8 or equivalent) and store at -70 C.
Preparation of Host for Male-Specific Coliphage Assay:
Step 1. Inoculate 5 mL of tryptone broth with E. coli Famp from a slant with an inoculating loop and incubate for 16 h at 36.5 ± 1 C.
1The term “male-specific coliphage” refers to coliphages whose receptor sites are located on the bacterial F-pilus. The E. coli Famp strain to be used for ICR monitoring will be provided to virus analytical laboratories by a U.S. EPA contractor.
IX-5
Step 2. Transfer 1.5 mL of the 16 h culture to 30 mL of tryptone broth in a 125 mL flask and incubate for 4 h at 36.5 ± 1 C with gentle shaking. The amount of inoculum and broth used in this step can be proportionally altered according to need.
Preparation of MS22 Positive Control:
Step 1. Rehydrate a stock culture of MS2 (American Type Culture Collection Product No. 15597-B1) and store at 4 C.
Step 2. Prepare a 30 mL culture of E. coli Famp as described in section titled Preparation of Host for Male-Specific Coliphage Assay. Incubate for 2 h at 36.5 ± 1 C with shaking. Add 1 mL of rehydrated phage stock and incubate for an additional 4 h at 36.5 ± 1 C.
Step 3. Filter the culture through a 0.45 µm sterilizing filter.
Step 4. Prepare 10-7, 10-8 and 10-9 dilutions of the filtrate using saline-calcium solution tubes.
These dilutions should be sufficient for most MS2 stocks. Some stocks may require higher or lower dilutions.
Step 5. Add 1 mL of the 10-9 dilution into each of five 16 × 150 mm test tubes. Using the same pipette, add 1 mL of the 10-8 dilution into each of five additional tubes and then 1 mL of the 10-7 dilution into five tubes. Label the tubes with the appropriate dilution.
Step 6. Add 0.1 mL of the host culture into each of the 15 test tubes from Step 5.
Step 7. Add 3 mL of the melted tryptone top agar held in the 44.5 ± 1 C water bath to one test tube at a time. Mix and immediately pour the contents of the tube over the bottom agar of a petri dish labeled with sample identification information. Rotate the dish to spread the suspension evenly over the surface of the bottom agar and place it onto a level surface to allow the agar to solidify.
Step 8. Incubate the inoculated plates at 36.5 ± 1 C overnight and examine for plaques the following day.
Step 9. Count the number of plaques on each of the 15 plates (don’t count plates giving plaque counts significantly more than 100). The five plates from one of the dilutions should give plaque counts of about 20 to 100 plaques. Average the plaque counts on these five plates and multiply the result by the reciprocal of the dilution to obtain the titer of the undiluted stock.
2The MS2 positive control strain or a mixture of male-specific coliphage strains to be used for positive or quality controls will be supplied to virus analytical laboratories by a
U.S. EPA contractor.
IX-6
Step 10. Dilute the filtrate to 30 to 80 PFU/mL in tryptone broth for use in a positive control in the coliphage assay. Store the original filtrate and the diluted positive control at 4 C.
Before using the positive control for the 1st time, place 1 mL each into ten 16 × 150 mm test tubes and assay using Steps 6-8. Count the plaques on all plates and divide by 10. If the result is not 30 to 80, adjust the dilution of the positive control sample and assay again.
Procedure for Male-Specific Coliphage Assay:
Step 1. Sample preparation:
- Add 1 mL of the water eluate sample to be tested to each of ten 16 × 150 mm test tubes.
- Add 1 mL of buffered 1.5% beef extract to a 16 × 150 mm test tube for a negative control.
- Add 1 mL of the diluted MS2 positive control to another 16 × 150 mm test tube.
Step 2. Add 0.1 mL of the host culture to each test tube containing eluate or positive control.
Step 3. Add 3 mL of the melted tryptone top agar held in the 44.5 ± 1 C water bath to one test tube at a time. Mix and immediately pour the contents of the tube over the bottom agar of a petri dish labeled with sample identification information. Tilt and rotate the dish to spread the suspension evenly over the surface of the bottom agar and place it onto a level surface to allow the agar to solidify.
Step 4. Incubate the inoculated plates at 36.5 ± 1 C overnight and examine for plaques the following day.
Step 5. Count the total number of plaques on the ten plates receiving the water eluate. Step 6. Male Specific coliphage enumeration.
IX-7
- Calculate the male specific coliphage titer (VM) in PFU per 100 L according to the formula:
V 100 × P × D × E
M I × C
where P is the total number of plaques from Step 5, D is the reciprocal of the dilution made on the inoculum before plating (D = 1 for undiluted samples) and E is the total vol- ume of eluate recovered (from the Virus Data Sheet of the Total Culturable Virus Proto- col). I is the total volume (in mL) of the eluate sample assayed on the ten plates. C is the amount of water sample filtered in liters (from the Sample Data Sheet of the Total Cul- turable Virus Protocol). Record the value of VM in the ICR database.
- Count the plaques on the positive control plate. Maintain a record of the plaque count as a check on the virus sensitivity of the bacterial host. Assay any water eluate samples again where the positive control counts are more than one log below their normal average.
IX-8
SECTION X. MEMBRANE FILTER METHOD FOR E. coli
- Citation: METHOD 1103.1, 1985
2. Scope
- 1 This method describes a membrane filter (MF) procedure for the detection and enumeration of Escherichia coli (E. coli). Because the bacterium is a natural inhabitant only of the intestinal tract of warm-blooded animals, its presence in water samples is an indication of fecal pollution and the possible presence of enteric pathogens.
- 2 The E. coli test is used as a measure of recreational water quality. Epidemiological studies have led to the development of criteria which can be used to promulgate recreational water standards based on established relationships between health effects and water quality. The significance of finding E. coli in recreational water samples is the direct relationship between the density of E. coli and the risk of gastrointestinal illness associated with swimming in the water (1).
- 3 The test for E. coli can be applied to fresh, estuarine and marine waters.
- 4 Since a wide range of sample volumes or dilutions thereof can be analyzed by the MF technique, a wide range of E. coli levels in water can be detected and enumer- ated.
- Summary – The MF method provides a direct count of bacteria in water based on the development of colonies on the surface of the membrane filter (2). A water sample is filtered through the membrane which retains the bacteria. After filtration, the membrane containing the bacterial cells is placed on a selective and differential medium, M-TEC, incubated at 35 C for 2 h to resuscitate injured or stressed bacteria, and then incubated at
44.5 C for 22 h. Following incubation, the filter is transferred to a filter pad saturated with urea substrate. After 15 min, yellow or yellow-brown colonies are counted with the aid of a fluorescent lamp and a magnifying lens.
- Definition – In this method, E. coli are those bacteria which produce yellow or yellow- brown colonies on a filter pad saturated with urea substrate broth after primary culturing on M-TEC medium.
- Interferences – Water samples containing colloidal or suspended particulate material can clog the membrane filter and prevent filtration, or cause spreading of bacterial colonies which could interfere with identification of target colonies.
X-1
6. Safety Precautions
- 1 The analyst/technician must know and observe the normal safety procedures required in a microbiology laboratory while preparing, using, and disposing of cultures, reagents and materials and while operating sterilization equipment.
- 2 Mouth-pipetting is prohibited.
7. Apparatus and Equipment
- 1 Glass lens, 2-5X magnification, or stereoscopic microscope.
- 2 Lamp with cool, white fluorescent tube and diffuser.
- 3 Hand tally or electronic counting device.
- 4 Pipet container, stainless steel, aluminum, or borosilicate glass, for glass pipets.
- 5 Pipets, sterile, T.D. bacteriological or Mohr, glass or plastic, of appropriate volume.
- 6 Graduated cylinders, covered with aluminum foil or kraft paper and sterile.
- 7 Membrane filtration units (filter base and funnel), glass, plastic or stainless steel, wrapped with aluminum foil or kraft paper and sterile.
- 8 Ultraviolet unit for sterilizing the filter funnel between filtrations (optional).
- 9 Line vacuum, electric vacuum pump, or aspirator for use as a vacuum source. In an emergency, or in the field, a hand pump, or a syringe equipped with a check valve to prevent the return flow of air, can be used.
- 10 Flask, filter vacuum, usually 1 L, with appropriate tubing. A filter manifold to hold a number of filter bases is optional.
- 11 Flask for safety trap, placed between the filter flask and the vacuum source.
- 12 Forceps, straight or curved, with smooth tips to handle filters without damage.
- 13 Ethanol, methanol or isopropanol in a small, wide-mouth container, for flame- sterilizing forceps.
- 14 Burner, Bunsen or Fisher type, or electric incinerator unit for sterilizing inoculation loops.
X-2
- 15 Thermometer, checked against a National Institute of Science & Technology (NIST) certified thermometer, or one traceable to an NIST thermometer.
- 16 Petri dishes, sterile, plastic, 50 × 12 mm, with tight-fitting lids, or 60 × 15 mm, glass or plastic, with loose-fitting lids. 100 × 15 mm dishes may also be used.
- 17 Bottles, milk dilution, borosilicate glass, screw-cap with neoprene liners, marked at 99 mL for 1-100 dilutions. Dilution bottles marked at 90 mL, or tubes marked at 9 mL may be used for 1-10 dilutions.
- 18 Flasks, borosilicate glass, screw-cap, 250-2000 mL volume.
- 19 Membrane filters, sterile, white grid marked, 47 mm diameter, with 0.45 ± 0.02 µm pore size.
- 20 Absorbent pads, sterile, 47 mm diameter (usually supplied with membrane filters).
- 21 Inoculation loops, at least 3 mm diameter, and needles, nichrome and platinum wire, 26 B & S gauge, in suitable holders. Disposable applicator sticks or plastic loops are alternatives to inoculation loops. Note: A platinum loop is required for the cytochrome oxidase test in 15.3.
- 22 Incubator maintained at 35 ± 0.5 C, with approximately 90 percent humidity if loose-lidded petri dishes are used.
- 23 Waterbath incubator maintained at 44.5 ± 0.2 C.
- 24 Waterbath maintained at 44-46 C for tempering agar.
- 25 Test tubes, 150 × 20 mm, borosilicate glass or plastic.
- 26 Test tubes, 75 × 10 mm, borosilicate glass.
- 27 Test tube caps, aluminum or autoclavable plastic, for 20 mm diameter test tubes.
- 28 Test tubes, screw-cap, 125 × 16 mm or other appropriate size.
X-3
8. Reagents and Materials
- 1 Purity of Reagents: Reagent grade chemicals shall be used in all tests. Unless otherwise indicated, reagents shall conform to the specifications of the Committee on Analytical Reagents of the American Chemical Society (3). The agar used in preparation of culture media must be of microbiological grade.
- 2 Whenever possible, use commercial culture media as a means of quality control.
- 3 Purity of Water: Reagent water conforming to Specification D1193, Type II water,
ASTM Annual Book of Standards (4).
- 4 Buffered Dilution Water
8.4.1 |
Composition: |
|
|
Sodium Dihydrogen Phosphate |
0.58 |
g |
|
Sodium Monohydrogen Phosphate |
2.50 |
g |
|
Sodium Chloride |
8.50 |
g |
- 4.2 Preparation: Dissolve the ingredients in 1 L of reagent water in a flask and dispense in appropriate amounts for dilutions in screw-cap bottles or culture tubes, and/or into containers for use as rinse water. Autoclave after preparation at 121 C (15 lb pressure) for 15 min. Final pH should be 7.4 ± 0.2.
- 5 M-TEC Agar (Difco 0334-15-0)
8.5.1 |
Composition: |
|
|
Proteose Peptone #3 |
5.0 |
g |
|
Yeast Extract |
3.0 |
g |
|
Lactose |
10.0 |
g |
|
NaCl |
7.5 |
g |
|
Dipotassium Phosphate |
3.3 |
g |
|
Monopotassium Phosphate |
1.0 |
g |
|
Sodium Lauryl Sulfate |
0.2 |
g |
|
Sodium Desoxycholate |
0.1 |
g |
|
Brom Cresol Purple |
0.08 |
g |
|
Brom Phenol Red |
0.08 |
g |
|
Agar |
15.0 |
g |
- 5.2 Preparation: Add 45.26 g of M-TEC medium to 1 L of reagent water in a flask and heat to boiling, until ingredients dissolve. Autoclave at 121 C (15 lb pressure) for 15 min. and cool in a 44-46 C waterbath. Pour the
X-4
medium into each 50 × 10 mm culture dish to a 4-5 mm depth (approxi- mately 4-6 mL) and allow to solidify. Final pH should be 7.3 ± 0.2. Store in a refrigerator.
8.6 Urea Substrate Medium
8.6.1 |
Composition: |
|
|
Urea |
2.0 |
g |
|
Phenol red |
0.01 |
g |
- 6.2 Preparation: Add dry ingredients to 100 mL reagent water in a flask. Stir to dissolve and adjust to pH 5.0 with a few drops of 1N HC1. The substrate solution should be a straw-yellow color at this pH.
- 7 Nutrient Agar (Difco 0001-02, BBL 11471)
8.7.1 |
Composition:
Peptone |
5.0 |
g |
|
Beef Extract |
3.0 |
g |
|
Agar |
15.0 |
g |
- 7.2 Preparation: Add 23 g of nutrient agar ingredients to 1 L of reagent water and mix well. Heat in boiling waterbath to dissolve the agar completely. Dispense in screw-cap tubes, bottles or flasks and autoclave at 121 C (15 lb pressure) for 15 min. Remove tubes and slant. The final pH should be 6.8
± 0.2.
- 8 Tryptic Soy Broth (Difco 0370-02) or Trypticase Soy Broth (BBL 12464)
8.8.1 |
Composition: |
|
|
Tryptone or Trypticase |
17.0 |
g |
|
Soytone or Phytone |
3.0 |
g |
|
Sodium Chloride |
5.0 |
g |
|
Dextrose |
2.5 |
g |
|
Dipotassium Phosphate |
2.5 |
g |
- 8.2 Preparation: Add 30 g of Tryptic (Trypticase) soy broth to 1 L of reagent water. Warm the broth and mix gently to dissolve the medium completely. Dispense in screw-cap tubes and autoclave at 121 C (15 lb pressure) for 15 min. The final pH should be 7.3 ± 0.2.
X-5
- 9 Simmons’ Citrate Agar (BBL 11619, Difco 0091-02)
8.9.1 |
Composition |
|
|
|
Magnesium Sulfate |
0.2 |
g |
|
Monoammonium Phosphate |
1.0 |
g |
|
Dipotassium Phosphate |
1.0 |
g |
|
Sodium Citrate |
2.0 |
g |
|
Sodium Chloride |
5.0 |
g |
|
Brom Thymol Blue |
0.08 |
g |
|
Agar |
15.0 |
g |
8.9.2 Preparation: Add 24.28 g of Simmons’ citrate agar to 1 L of reagent water. Heat in boiling waterbath with mixing for complete solution. Dispense in screw-cap tubes and sterilize at 121 C (15 lb pressure) for 15 min. Cool tubes as slants. The final pH should be 6.8 ± 0.2.
- 10 Tryptone (Difco 0123-02) or Trypticase Peptone (BBL 11920) Broth
8.10.1 Composition:
Tryptone or Trypticase peptone 10.0 g
- 10.2 Preparation: Add 10 g of tryptone or trypticase peptone to 900 mL of reagent water and heat with mixing until dissolved. Bring solution to 1000 mL in a graduate or flask. Dispense in five mL volumes in tubes and autoclave at 121 C (15 lb pressure) for 15 min. The final pH should be 7.2
± 0.2.
- 11 EC Broth (Difco 0314-02) or EC Broth (BBL 12432)
8.11.1 |
Composition: |
|
|
Tryptose or Trypticase Peptone |
20.0 |
g |
|
Lactose |
5.0 |
g |
|
Bile Salts No. 3 or |
|
|
|
Bile Salts Mixture |
1.5 |
g |
|
Dipotassium Phosphate |
4.0 |
g |
|
Monopotassium Phosphate |
1.5 |
g |
|
Sodium Chloride |
5.0 |
g |
8.11.2 Preparation: Add 37 g of EC medium to 1 L of reagent water and warm to dissolve completely. Dispense into fermentation tubes (150 × 20 mm tubes containing inverted 75 × 10 mm vials). Sterilize at 121 C (15 lb pressure) for 15 min. The final pH should be 6.9 ± 0.2.
X-6
- 12 Cytochrome Oxidase Reagent: N, N, N1, N1 tetramethyl-p-phenylenediamine dihydrochloride, 1% aqueous solution.
- 13 Kovacs’ Indole Reagent: Dissolve 10 g p-dimethylaminobenzaldehyde in 150 mL amyl or isoamyl alcohol and then slowly add 50 mL concentrated hydro- chloric acid and mix.
9. Sample Collection, Preservation and Holding Times
- 1 Sampling procedures are described in detail in the USEPA Microbiology Methods Manual, Section II, A (5). Adherence to sample preservation procedures and holding time limits is critical to the production of valid data. Samples not collected according to these rules should not be analyzed.
- 1.1 Storage Temperature and Handling Conditions: Ice or refrigerate water samples at a temperature of 1-4 C during transit to the laboratory. Use insulated containers to assure proper maintenance of storage temperature. Take care that sample bottles are not totally immersed in water during transit or storage.
- 1.2 Holding Time Limitations: Examine samples as soon as possible after collection. Do not hold samples longer than 8 h between collection and initiation of analyses.
10. Calibration and Standardization
- 1 Check temperatures in incubators daily to insure operation within stated limits.
- 2 Check thermometers at least annually against an NIST certified thermometer or one traceable to NIST. Check mercury columns for breaks.
11. Quality Control
- 1 See recommendations on quality control for microbiological analyses in the
USEPA Microbiology Methods Manual , Part IV, C (5).
12. Procedures
- 1 Prepare the M-TEC agar and urea substrate as directed in Sections 8.5 and 8.6.
- 2 Mark the petri dishes and report forms with sample identification and sample volumes.
X-7
- 3 Place a sterile membrane filter on the filter base, grid-side up and attach the funnel to the base; the membrane filter is now held between the funnel and the base.
- 4 Shake the sample bottle vigorously about 25 times to distribute the bacteria uniformly and measure the desired volume of sample or dilution into the funnel.
- 5 For ambient surface waters and waste waters, select sample volumes based on previous knowledge of pollution level, to produce 20-80 E. coli colonies on the membranes. Sample volumes of 1-100 mL are normally tested at half-log intervals.
- 6 Smaller sample size or sample dilutions can be used to minimize the interference of turbidity or high bacterial densities. Multiple volumes of the same sample dilution may be filtered and the results combined.
- 7 Filter the sample and rinse the sides of the funnel at least twice with 20-30 mL of sterile rinse water. Turn off the vacuum and remove the funnel from the filter base.
- 8 Use sterile forceps to aseptically remove the membrane filter from the filter base and roll it onto the M-TEC agar to avoid the formation of bubbles between the membrane and the agar surface. Reseat the membrane, if bubbles occur. Close the dish, invert, and incubate at 35 C for 2 h.
- 9 After 2 h incubation at 35 C, transfer the plates to Whirl-Pak bags, seal, and place inverted in a 44.5 C waterbath for 22-24 h.
- 10 After 22-24 h, remove the dishes from the waterbath. Place absorbent pads in new petri dishes or the lids of the same petri dishes, and saturate with urea broth. Aseptically transfer the membranes to absorbent pads saturated with urea substrate and hold at room temperature.
- 11 After 15-20 min. incubation on the urea substrate at room temperature, count and record the number of yellow or yellow-brown colonies on those membrane filters ideally containing 20-80 colonies.
X-8
13. Calculation of Results
13.1 Select the membrane filter with the number of colonies within the acceptable range (20-80) and calculate the count per 100 mL according to the general formula:
- coli/100 mL = No. E. coli Colonies Counted
Volume in mL of Sample Filtered
× 100 mL
13.2 See general counting rules in the USEPA Microbiology Methods Manual , Part II, C, 3.5 (5).
14. Reporting Results
- 1 Report the results as E. coli per 100 mL of sample.
15. Verification Procedure
- 1 Yellow or yellow-brown colonies from the urease test can be verified as E. coli. Verification of colonies may be required in evidence gathering, and is also recommended as a QC procedure with initial use of the test and with changes in sample sites, lots of commercial media or major ingredients in media com- pounded in the laboratory. The verification procedure follows:
- 1.1 Using a sterile inoculation loop, transfer growth from the centers of at least 10 well-isolated typical colonies to nutrient agar plates or slants and to Tryptic (Trypticase) soy broth. Incubate the agar and broth cultures for 24 h at 35 C.
- 1.2 After incubation remove a generous portion of material from the nutrient agar with a platinum loop and deposit on the surface of filter paper that has been saturated with cytochrome oxidase reagent prepared fresh that day. A positive test is indicated within 15 s by the development of a deep purple color where the bacteria were deposited.
- 1.3 Transfer growth from the Tryptic (Trypticase) soy broth to Simmons’ citrate agar, Tryptone (Trypticase peptone) broth and EC broth in a fermentation tube. Incubate the Simmons’ citrate agar for 24 h and Tryptone (Trypticase peptone) broth for 48 h at 35 C. Incubate the EC broth at 44.5 C in a waterbath for 24 h. The water level must be above the level of the EC broth in the tube. Add one-half mL of Kovacs’ indole reagent to the 48 h Tryptone (Trypticase peptone) broth culture and shake the tube gently. A positive test for indole is indicated by a deep red color which develops in
X-9
the alcohol layer. E. coli is EC gas positive, indole positive, oxidase negative, and does not grow on citrate medium.
16. Precision and Bias
- 1 Performance Characteristics
- 1.1 Precision – The degree of agreement of repeated measurements of the same parameter expressed quantitatively as the standard deviation or as the 95% confidence limits of the mean computed from the results of a series of controlled determinations. The M-TEC method precision was found to be fairly representative of what would be expected from counts with a Poisson distribution (2).
- 1.2 Bias – The persistent positive or negative deviation of the average value of the method from the assumed or accepted true value. The bias of the M- TEC method has been reported to be -2% of the true value (2).
- 1.3 Specificity – The ability of a method to select and/or distinguish the target bacteria under test from other bacteria in the same water sample. The specificity characteristic of a method is usually reported as the percent of false-positive and false-negative results. The false-positive rate reported for M-TEC medium averaged 9% for marine and fresh water samples. Less than 1% of the E. coli colonies observed gave a false-negative reaction (2).
- 1.4 Upper Counting Limit (UCL) – That colony count above which there is an unacceptable counting error. The error may be due to overcrowding or antibiosis. The UCL for E. coli on M-TEC medium has been reported as 80 colonies per filter (2).
16.2 Collaborative Study Data
- 2.1 A collaborative study was conducted among eleven volunteer laboratories, each with two analysts who independently tested local fresh and marine recreational waters and sewage treatment plant effluent samples, in dupli- cate. The data were reported to the Environmental Monitoring and Support Laboratory – Cincinnati, Ohio, U.S. Environmental Protection Agency, for statistical calculations.
- 2.2 The results of the study are shown in Figure X-1 where So equals standard deviation among replicate counts from a single analyst and Sb equals standard deviation between means of duplicates from analysts in the same
X-10
Figure X-1. Precision Estimates for E. coli in Water by the Membrane Filter M-TEC Method
SO = Standard Deviation among Replicate Counts from a Single Analyst
SB = Standard Deviation between the Means of Duplicate Counts by Analysts in the Same Laboratory
laboratory. The precision estimates from this study did not show any difference among the water types analyzed.
- 2.3 The precision of the method can be generalized as: So = 0.028 count/100 mL + 6.11 (dilution factor) and
Sb = 0.233 count/100 mL + 0.82 (dilution factor), where the
dilution factor =
100
VOLUME OF ORIGINAL SAMPLE FILTERED
- 2.4 Because of the instability of microbial populations in water samples, each laboratory analyzed its own sample series and no full measure of recovery or bias was possible. However, all laboratories analyzed a single surrogate sample prepared from a freeze-dried culture of E. coli. The mean count (x) and the overall standard deviation of the counts (St) (which includes the variability among laboratories for this standardized E. coli sample) were 31.6 colonies/membrane and 7.61 colonies/membrane, respectively.
17. REFERENCES
- Cabelli, V.J., A.P. Dufour, M.A. Levin, L.J. McCabe, and P.W. Haberman. 1979. Relationship of Microbial Indicators to Health Effects at Marine Bathing Beaches. Amer. Jour. Public Health 69:690-696.
- Dufour, A.P., E. Strickland, and V.J. Cabelli. 1981. Membrane Filter Method for Enumerating Escherichia coli. Appl. and Environ. Microbiol. 41:1152-1158.
- Reagent Chemicals. 1981. American Chemical Society Specifications, 6th Edition, Am. Chem. Soc., Washington, D.C. For suggestions on the testing of reagents not listed by the American Chemical Society, see Reagent Chemicals and Standards. 1967. Joseph Rosin, D. Van Nostrand Co., Inc., Princeton, N.J., and the United States Pharmacopeia, Nineteenth Edition. 1974. United States Pharmacopeial Convention, Inc., Rockville, Md.
- Annual Book of ASTM Standards. 1985. Vol. 1101, Water, American Society for Testing and Materials, Philadelphia, PA.
- Bordner, R., J.A. Winter and P.V. Scarpino (eds.). 1978. Microbiological Methods for Monitoring the Environment. Water and Wastes, EPA-600/8-78-077, U.S. Environmen- tal Protection Agency, Office of Research and Development, Environmental Monitoring Support Laboratory – Cincinnati, Cincinnati, Ohio.
X-12
SECTION XI. MEMBRANE FILTER METHOD FOR C. perfringens
1. Scope and Application
- 1 This procedure enumerates Clostridium perfringens spores from surface and drinking water. Since C. perfringens is present in large numbers in human and animal wastes and its spores are resistant to wastewater treatment practices, extremes in temperature and environmental stress, it is an indicator of present fecal contamination as well as a conservative tracer of past fecal contamination. Some investigators have proposed C. perfringens as an indicator of the presence and the density of pathogenic viruses and possibly other microorganisms.
- 2 It is the user’s responsibility to insure the validity of this method for untested matrices.
- Summary of Method – An appropriate volume of water sample is passed through a membrane filter that retains the bacteria present in the sample. The membrane filter is placed on mCP agar and incubated anaerobically for 24 h at 44.5 C using a medium modified by Armon and Payment from Bisson and Cabelli (1,2). Upon exposure to ammonium hydroxide, the yellow straw-colored C. perfringens colonies turn dark pink to magenta and are counted as presumptive C. perfringens. Because of the selectivity of the mCP medium, a presumptive count is normally reported for routine monitoring purposes. Verification is not required for ICR monitoring, but if desired, colonies are confirmed by anaerobic growth in thioglycollate, a positive gram stain reaction and stormy fermentation of iron milk. The mCP counts are adjusted based on the percent confirmation. This method was originally prepared by Irwin Katz, U.S. EPA Region 2 for ASTM Subcom- mittee D19.24, Water Microbiology.
3. Definitions
- 1 C. perfringens – An obligate anaerobic gram-positive, spore forming, non-motile bacillus that ferments lactose with stormy gas production and ferments sucrose but does not ferment cellobiose. C. perfringens produces acid phosphatase and also produces exotoxins which cause gas gangrene and gastroenteritis.
- 2 Spores – C. perfringens produces single oval subterminal spores less than 1 µm in diameter during adverse conditions. Sporulation can also occur in the intestinal tract. The endospore that develops is a highly refractile body formed within the cell. Spores are resistant to heat, drying and chemical disinfectants, which would kill the vegetative cells of C. perfringens. This resistance to unfavorable conditions preserves the organisms for long periods of time.
XI-1
4. Interferences
- 1 Waters containing sediment or large quantities of colloidal or suspended materials such as iron, manganese, alum floc or algae can clog the filter pores and prevent filtration, or can cause the development of spreading bacterial colonies that mask other colonies and prevent accurate counting.
- 2 When bacterial densities are high, a smaller sample volume or sample dilution can be filtered to minimize the interference of turbidity or high background (non-target) bacterial densities. Replicates of smaller sample volumes or dilutions of sample may be filtered and the results combined. However, the membrane filter technique may not be applicable to highly turbid waters with low Clostridium densities.
- 3 Toxic materials such as metals, phenols, acids, caustics, chloramines, and other disinfection by-products may also adversely affect recovery of Clostridium vegeta- tive cells on the membrane filter. Although most probable number (MPN) methods are not usually expected to generate results comparable to membrane filter meth- ods, an MPN method should be considered as an alternative procedure if the membrane filter method is not useable for these samples (3).
- 4 Some lots of membrane filters produce low recoveries or poor differentiation of target and non-target colonies due to toxicity, chemical composition, or structural defects. Quality control checks should be made on new lots of membranes (4).
5. Health and Safety
- 1 This method does not address all safety problems associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and determine regulatory limitations prior to use.
- 2 The analyst/technician must know and observe normal good laboratory practices and safety procedures required in a microbiology laboratory while preparing, using and disposing of cultures, reagents and materials and while operating sterilizers and other equipment and instrumentation.
- 3 Mouth-pipetting is not permitted.
XI-2
6. Instruments, Equipment and Supplies
- 1 Sample container, sterile, non-toxic glass or rigid plastic with screw cap, or plastic bag, minimum of 125 mL capacity.
- 2 Pipet container, stainless steel, or aluminum, for sterilization and storage of glass pipets.
- 3 Pipets, sterile T.D. bacteriological or Mohr, glass or plastic, of appropriate volumes.
- 4 Graduated cylinders, 100 to 1000 mL, tops are covered with aluminum foil or kraft paper and sterilized.
- 5 Bottles, milk dilution, borosilicate glass or non-toxic heat stable plastic, screw-cap with neoprene liners, marked at 99 mL for 1:100 dilutions. Dilution bottles marked at 90 mL or tubes marked at 9 mL may be used for 1:10 dilutions.
- 6 Membrane filtration units, (filter base and funnel), glass, plastic or stainless steel, wrapped with aluminum foil or kraft paper and sterilized.
- 7 Membrane Filters – sterile, white, grid marked, 47 mm diameter, with 0.45 ± 0.02
µm pore size or other pore sizes for which the manufacturer provides data demon- strating equivalency.
- 8 Ultraviolet unit for disinfecting the filter funnel between filtrations in a series (optional).
- 9 Line vacuum, electric vacuum pump or aspirator as a vacuum source.
- 10 Flask, vacuum, usually 1 L, with appropriate tubing, to hold filter base. Filter manifolds to hold a number of filter bases are optional.
- 11 Flask, safety trap, placed between the filter flask and the vacuum source.
- 12 Forceps, straight or curved, with smooth tips to permit handling of filters without damage.
- 13 Petri plates, plastic or glass, 50 × 9 mm, with tight-fitting lids, or 60 × 12 mm, with loose fitting lids (dimensions are nominal).
- 14 Test Tubes, 20 × 150 mm, borosilicate glass or disposable plastic.
- 15 Caps, aluminum or autoclavable plastic, for 20 × 150 mm test tubes.
XI-3
- 16 Test Tubes, screw cap, 16 × 125 mm or other appropriate size.
- 17 Inoculation loops, 3 mm diameter, and needles, nichrome or platinum wire, 26 B & S gauge, in suitable holders. Sterile disposable applicator sticks or plastic loops are acceptable alternatives to inoculation loops.
- 18 Thermometers, 0-50 C, graduated to 0.2 degrees, and 0-100 C for heat shock which has been checked against the appropriate National Institute of Standards and Technology (NIST) certified thermometer, or against a thermometer traceable to NIST.
- 19 Waterbath, that maintains 46-48 C for tempering agar.
- 20 Waterbath with gable cover that maintains 60 C ± 0.5 C for heat shocking samples.
- 21 Anaerobic system (anaerobic jar, reaction chamber, hydrogen/carbon dioxide disposable generator and anaerobic indicator), or any other system capable of producing the appropriate anaerobic conditions to support the growth of the organisms1.
- 22 Filter Paper, circular, 11 cm, Whatman 40 or 110, or equivalent, for separation of mCP agar plates during anaerobic incubation.
- 23 Incubator, that maintains 44.5 C ± 0.2 C and is large enough to hold the anaerobic chamber.
- 24 Incubator, Water Bath, that maintains 44.5 C ± 0.2 C for incubation of Iron Milk Medium.
- 25 Microscope, stereoscopic, wide-field type, with magnification of 10 to 15X.
- 26 Microscope lamp, that produces diffuse light from a cool white fluorescent or tungsten lamp adjusted to give maximum visibility.
- 27 Counting device, hand tally or electronic.
1BBL 60460 or BBL 60466 GASPAK Anaerobic System with BBL 70308 Disposable Hydrogen and Carbon Dioxide Generator Envelopes, BBL Microbiological Systems,
Cockeysville, MD 21030, or equivalent.
XI-4
6.28 Sonication unit, to aid in dissolving reagents.2
7. Reagents, Standards and Media
- 1 Purity of Reagents – Use reagent grade chemicals in all tests. Unless otherwise indicated, all reagents must conform to the specifications of the Committee on Analytical Reagents of the American Chemical Society where such specifications are available (5). Other grades may be used, provided it is first ascertained that the reagent is of sufficiently high purity to permit its use without lessening the accuracy of the determination. Use microbiological grade agar in preparation of culture media. Whenever possible, use commercial culture media as a means of improved quality control.
- 2 Purity of Water – Unless otherwise indicated, references to water mean reagent water as defined by Type II of Specification D1193 (6).
7.3 Buffered Dilution and Rinse Water
- 3.1 Phosphate Buffer Dilution Water
- 3.1.1 Stock Phosphate Buffer Solution – Dissolve 34.0 g of potassium dihydrogen phosphate (KH2PO4) in 500 mL of water. Adjust pH to
7.2 with 1 N NaOH and bring to 1000 mL with water. Dispense
aseptically into screw-cap bottles and autoclave for 15 min at 121 C. Alternatively, sterilize by filtration through a 0.2 µm pore membrane filter and dispense aseptically into sterile screw-cap bottles. Store in refrigerator and handle aseptically. If cloudiness, a marked change in pH, or other evidence of contamination appears, discard the stock.
Confirm that pH is 7.2 ± 0.5 before use.
- 3.1.2 Magnesium Chloride Solution – Dissolve 81.4 g of hexahydrate magnesium chloride (MgCl2 6H20) in 1000 mL of water. Mix well and sterilize by filtration or autoclave for 15 min at 121 C. Store in refrigerator and handle aseptically. If cloudiness, or other evidence of contamination occurs, discard the stock solution.
- 3.1.3 Phosphate Buffered Dilution Water – Add 1.25 mL of stock phos- phate buffer solution and 5 mL of magnesium chloride solution to 1000 mL of water in a volumetric flask and mix well. Dispense dilution water in amounts which will provide 99 ± 2 mL after sterili-
2Bronson Sonifier, 500 W, or Tekmar Sonic Disrupter, 500 W with 3 mm tip set at 18 W, or equivalent.
XI-5
zation in screw-cap dilution bottles, or in larger volume containers for use as rinse water. Autoclave dilution bottles for 15 min at 121 C. Autoclave larger volumes for longer periods as appropriate. Alterna- tively, sterilize by filtration through a sterile 0.2 µm pore membrane filter unit and dispense aseptically into sterile screw-cap bottles.
7.3.2 Peptone Dilution and Rinse Water – Dissolve 1.0 g of peptone3 in 100 mL of water, and bring to 1000 mL with water. Dispense in screw-cap bottles in volumes to produce 99 ± 2 mL after autoclaving. Autoclave for 15 min. at 121 C. Final pH should be 6.8 – 7.0. Adjust as necessary.
- 4 Ethanol – 95%, pure, for flame-sterilization of forceps and for preparation of acetone alcohol for gram stain.
- 5 Ammonium Hydroxide Solution (29.2% NH4OH) – commercially available.
- 6 Ferric Chloride Solution – Weigh out 4.5 g of FeC13 6H20 and dissolve in 100 mL of water. Filter sterilize and store in refrigerator.
- 7 Phenolphthalein diphosphate Solution – Weigh out 0.5 g of phenolphthalein diphosphate and dissolve in 100 mL of water. Filter sterilize and store in refrigera- tor.
- 8 Indoxyl -D Glucoside Solution – Weigh out 0.06 g of Indoxyl -D Glucoside and dissolve in 80 mL of water (0.075 solution). Sonicator (item 6.28) can be used to speed dissolution. Filter-sterilize and use in 7.9.2.
7.9 Modified mCP Agar (1)
7.9.1 |
Composition/L |
|
|
Tryptose |
30.0 |
g |
|
Yeast Extract |
20.0 |
g |
|
Sucrose |
5.0 |
g |
|
L-cysteine Hydrochloride |
1.0 |
g |
|
MgSO4 7H20 |
0.1 |
g |
|
Bromcresol Purple |
0.04 |
g |
|
Agar |
15.0 |
g |
- 9.2 Preparation of Modified mCP Agar: Add medium ingredients from
7.9.1 to 900 mL water in a liter Erlenmeyer flask. Stir and heat to dissolve in a boiling water bath. Bring the pH to 7.6 with 1 N NaOH. Autoclave for
3Peptone (Difco 0118), Difco Laboratories, Detroit, MI, or equivalent.
XI-6
15 min at 121 C (15 lbs pressure). Cool to 50 C. Add the following reagents aseptically and mix well:
D-cycloserine |
0.4 |
g |
Polymyxin B sulfate |
0.025 |
g |
4.5% FeCl3 6H20 solution |
2.0 |
mL |
0.5% Phenolphthalein diphosphate solution |
20.0 |
mL |
0.075% -D-Glucoside solution |
80.0 |
mL |
- 9.3 Dispense 4-4.5 mL into each petri plate using a sterile Cornwall syringe or Brewer pipette. Store agar plates inverted in a plastic bag in a refrigerator for no more than one month. It is recommended that the plates be stored in an anaerobic chamber in the refrigerator for optimal preservation.
7.10 Modified Iron Milk Medium (7)
Fresh pasteurized, homogenized milk
(3.5% butterfat) 1.0 L
FeSO4 7H2O 1.0 g
- 10.2 Preparation: Dissolve ferrous sulfate in 50 mL water. Add slowly to 1 L milk and mix with magnetic stirrer. Dispense 11 mL of medium into culture tubes. Cap and autoclave 12 min at 118 C. CAUTION: Do not exceed the recommended time and temperature limits to avoid coagulation.
7.11 |
Fluid Thioglycollate Medium 4
7.11.1 Composition/L
L-Cystine |
0.5 |
g |
|
Agar (granulated) |
0.75 |
g |
|
NaCl |
2.5 |
g |
|
Dextrose (anhydrous) |
5.0 |
g |
|
Yeast extract |
5.0 |
g |
|
Tryptone |
15.0 |
g |
|
Sodium thioglycollate |
0.5 |
g |
|
Resazurin |
0.001 |
g |
4Fluid Thioglycollate Medium (BBL 12461), Becton-Dickinson Microbiology Systems, Cockeysville, MD; (Difco 0432-02-6) Difco Laboratories, Detroit, MI; or equivalent.
XI-7
7.11.2 Preparation: Suspend 29.25 g of medium in 1 L of water. Mix thor- oughly and heat to boil for 1-2 min or until solution is complete. Final pH is 7.1 ± 0.1. Dispense 15 mL portions into culture tubes. Cap and auto- clave for 15 min at 121 C. Store tubes in the dark at room temperature. Do not refrigerate. If medium becomes oxidized (more than 30% of medium is pink), reheat once only in boiling water bath and cool before use.
7.12 Gram Stain Reagents
- 12.1 Gram stain reagent kits are commercially available and are recommended.
- 12.2 Ammonium oxalate-crystal violet (Hucker’s) : Dissolve 2 g crystal violet (90% dye content) in 20 mL 95% ethyl alcohol. Dissolve 0.8 g
(NH4)2C2O4 H2O in 80 mL water; mix the two solutions and age for 24 h before use. Filter through a 0.22 µm membrane filter. Store in a glass bottle.
- 12.3 Lugol’s solution, Gram’s modification : Grind 1 g iodine crystals and 2 g KI in a mortar. Add water, a few mL at time, and grind thoroughly after each addition until solution is complete. Filter solution through a 0.22 µm membrane filter, and rinse into an amber glass bottle with the remaining water (using a total of 300 mL).
- 12.4 Counterstain: Dissolve 2.5 g safranin dye in 100 mL 95% ethyl alcohol. Add 10 mL to 100 mL water. Filter through a 0.22 µm membrane filter.
- 12.5 Acetone alcohol: Mix equal volumes of ethyl alcohol (95%) with acetone.
8. Sample Collection, Preservation and Holding Times
- 1 Collection – Water samples are collected in sterile sample containers with leak- proof lids.
- 2 Sample Preservation and Holding Conditions – Hold water samples at a temper- ature below 10 C during transit to the laboratory by placing them on ice, surround- ing them with blue ice or by refrigeration. Use insulated containers to maintain storage temperature during transit. Take care that sample bottle closures are not submerged in water during transit or storage.
- 3 Holding Time – Refrigerate samples upon arrival in the laboratory and analyze within 8 h after collection. C. perfringens spores can survive for extended periods
XI-8
at 1-4 C. However, since a correlation is planned with other indicators, the holding time for C. perfringens must be limited to that of the other indicators.
9. Quality Control
- 1 Adherence to sampling procedures, preservation procedures and holding time limits is critical to the production of valid data. Reject samples if appropriate sampling, preservation and handling procedures have not been followed
- 2 Check and record temperatures in incubators daily to insure operation within stated limits.
- 3 Check thermometers at least annually against a National Institute of Standards and Technology (NIST) certified thermometer or one traceable to NIST and record the results. Examine mercury columns for separation and reunite before use. Adjust or post correction factors on equipment.
- 4 Use a loop to inoculate mCP agar plates with pure cultures of C. perfringens and E. coli. Carry these plates through the entire analytical procedure, as positive and negative controls.
- 5 For general quality control recommendations, see “Quality Assurance for Microbi- ological Analyses” in ASTM Special Technical Testing Publication 867 (8).
10. Procedure for Analyses of Water Samples for Spores
- 1 Prepare mCP Agar according to Section 7.9.
- 2 Mark the bottoms of the petri plates and laboratory data sheets with sample identities and volumes.
- 3 Grasp a sterile membrane filter by its edge using a sterile forceps and place on the filter base, grid side up. Attach the funnel to the base of the filter unit; the mem- brane filter is now held between the funnel and the base.
- 4. Procedure for Inactivation of Vegetative Cells – To obtain a count only of C. perfringens spores, hold water samples in a waterbath at 60 C for 15 min to kill all vegetative cells.
- 4.1 Equilibrate a waterbath at 60 C.
- 4.2 Determine the time necessary to bring a blank sample to 60 C. Use the same size container and volume as used for water samples.
XI-9
- 4.3 Immerse the containers containing the water samples in the waterbath for the time necessary to warm sample to 60 C plus 15 min. Do not allow the container cap or container opening to become contaminated by water in the bath.
- 4.4 Cool the sample containers in cold tap water immediately after heat shock and proceed with the analyses in 10.3.
- 5 For greatest accuracy, it is necessary to filter a sample volume that will yield a countable plate. Select sample volumes based on previous knowledge, which will produce membrane filter plates with 20-80 C. perfringens colonies. A narrow range of dilution factors of 4 or 5 can usually be used to achieve the desired number of colonies. An example of such factors is shown in Table XI-1. How- ever, if past analyses of specific samples have resulted in confluent growth or “too numerous to count” (TNTC) membranes from excessive turbidity, additional samples should be collected and filtration volumes adjusted to provide isolated colonies from one or more smaller volumes. The counts from smaller volumes can be combined for a final count/total volume filtered.
- 6 Shake the sample bottle vigorously about 25 times and measure the desired volume of sample into the funnel with the vacuum off. To measure the sample accurately and obtain good distribution of colonies on the filter surface, use the following procedures:
- 6.1 Sample volumes of 20 mL or more: Measure the sample in a sterile grad- uated cylinder and pour it into the funnel. Rinse the graduate twice with sterile dilution water, and add the rinse water to the funnel.
- 6.2 Sample volumes of 10-20 mL: Measure the sample with a sterile 10 mL or 20 mL pipet into the funnel.
- 6.3 Sample volumes of 1-10 mL: Pour about 10 mL of sterile dilution water into the funnel without vacuum. Add the sample to the sterile water using appropriate sterile pipet and filter the sample.
- 6.4 Sample volumes of less than 1.0 mL: Prepare appropriate dilutions in sterile dilution water and proceed as applicable in steps 10.6.1-10.6.3 above.
- 6.5 To reduce the chance for carryover, when analyzing a series of samples or dilutions, filter samples in the order of increasing volumes of original sample. The time elapsing between preparation of sample dilutions and filtration should be minimal and never more than 30 min.
XI-10
Table XI-1. Sample Volumes to Obtain Colony Count on Membrane Filters *
(Range of 20 – 80 Colonies) |
Sample Volume in mL |
Added as: |
0.05 |
5.0 |
mL of 10-2 dilution |
0.20 |
2.0 |
mL of 10-1 dilution |
0.80 |
8.0 |
mL of 10-1 dilution |
3.20 |
3.2 |
mL of Undiluted Sample |
15.00 |
15.0 |
mL of Undiluted Sample |
60.00 |
60.0 |
mL of Undiluted Sample |
*The range of volumes and dilutions selected for filtration of completely unknown samples can be broader, to provide a factor of 10 or more.
Prepare at least three sample increments. |
- 7 After adding the sample to filter funnel, turn on vacuum and filter the sample. Rinse the sides of the funnel walls at least twice with 20-30 mL of sterile dilution water. Turn off vacuum and remove the funnel from the filter base.
- 8 Flame forceps, cool and aseptically remove the membrane filter from the filter base. Place the filter, grid side up, on the mCP agar using a rolling motion to prevent air bubbles. Reseat the filter if bubbles occur.
- 9 Remove the lids from mCP agar plates. Invert lids and nest them under the corresponding plate bottom for identification. Stack the plates in layers in the anaerobic chamber, separating each plate with sterile filter paper. Incubate the anaerobic chamber at 44.5 C for 24 h, maintaining anaerobic conditions through the use of a commercial anaerobic system. If visible condensation does not occur within 60 min after the BBL GasPak is activated, the reaction should be terminated by opening the jar, and removing the GasPak. Inspect the chamber seal for alignment and lubricant. Insert a new GasPak and seal the chamber. The dispos- able anaerobic indicator (moistened flat fiber wick impregnated with 0.35% methylene blue solution) is white to pale blue upon opening foil envelope. It turns blue upon exposure to air. Under anaerobic conditions the methylene blue indica- tor will decolorize (turn white) within 2 – 4 h. It should remain white through the incubation period.
- 10 After 24 h, remove one agar plate at a time from the chamber and reclose the chamber. Examine the mCP plate for straw-yellow colonies. If such colonies are
XI-11
present, invert and expose the open agar plate 10-30 sec to the fumes from an open container of concentrated ammonium hydroxide.
- 11 If C. perfringens colonies are present, the phosphate in the phenolphthalein diphosphate will be cleaved from the substrate by acid phosphatase and typical colonies of C. perfringens will turn a dark pink or magenta after exposure to fumes of ammonium hydroxide.
- 12 Count pink or magenta colonies as presumptive C. perfringens.
- 13 Repeat steps 10.10 to 10.12 with the other culture plates.
11. Confirmation Tests
- 1 Pick at least 10 typical isolated C. perfringens colonies from the mCP plate and transfer each into a separate thioglycollate tube. Incubate at 35 C for 24 h. Examine by gram stain and for purity. C. perfringens are short gram-positive bacilli. Retain tubes for further testing.
- 2 Inoculate ten tubes of iron milk medium with 1 mL from the ten fluid thioglycollate tubes and incubate in a 44.5 C waterbath for two h. Examine hourly for stormy fermentation with rapid coagulation and fractured rising curd.
- 3 Those colonies which are gram-positive, non-motile, and produce stormy fermenta- tion of milk in these confirmatory tests are considered confirmed C. perfringens.
12. Data Analyses, Calculations and Reporting Results
- 1 Pink or magenta colonies counted on mCP medium are adjusted to a count/100 mL and reported as: Presumptive C. perfringens colony forming units (CFU)/100 mL. The presumptive count is normally used for routine monitoring.
- 2 If confirmation tests are performed, original counts on mCP agar are adjusted based on the percent of colonies picked and confirmed. Report as confirmed C. perfringens CFU/100 mL of water sample.
13. Method Performance Characteristics
- 1 The detection limit is one C. perfringens CFU per sample volume or sample dilution tested.
XI-12
- 2 The false positive rate is reported to be 7-9% by Bisson and Cabelli (2) and Fujioka and Shizumura (10). The false negative rate is reported to be 3% by Fujioka and Shizumura (10).
- 3 The single laboratory recovery is reported to be 79-90% by Bisson and Cabelli (2).
- 4 In a collaborative study, sixteen analysts from nine laboratories analyzed a sedi- ment, a non-chlorinated wastewater and three spiked waters (marine water, lake water and a finished drinking water), as unknowns. Analysts were provided range values to reduce the number of dilutions necessary for the analyses.
- 4.1 The single operator precision as % Relative Standard Deviation (RSD) ranged from 14-28% while the overall precision (as % RSD) ranged from 24-41%, for St/So (overall precision/single operation precision) ratios of 1.13-1.80. The larger RSD values were not generated with the more difficult sample matrices of sediment and wastewater. Rather, they oc- curred with the seeded finished drinking water sample and are believed to have been caused by overestimates of the concentration of C. perfringens, which resulted in marginally low plate counts with inherently greater deviations. Overall, the St and So values were similar across sample types and concentration levels of C. perfringens.
- 4.2 Although there were no “standards” available for this RR study, sample 5, a seeded drinking water, had a reference count of 78 C. perfringens CFU/100 mL. The laboratories in this study achieved a mean recovery of 67 CFU from Sample 5 for an 86 percent recovery.
- 4.3 Table XI-2 contains the statistical summary of the collaborative study results.
Table XI-2. Statistical Evaluation of Results (CFU/100 mL) (After Rejection of Outliers) |
Sample |
Initial n |
Final n |
X |
S0 |
St |
%RSD (So) |
%RSD (St) |
1 |
30 |
30 |
2893.63 |
397.78 |
715.45 |
13.75 |
24.73 |
2 |
36 |
35 |
108.09 |
20.34 |
26.18 |
18.82 |
24.22 |
3 |
30 |
30 |
73.07 |
20.29 |
23.23 |
27.77 |
31.79 |
4 |
36 |
35 |
5985.71 |
1400.70 |
1585.80 |
23.40 |
26.49 |
5 |
27 |
27 |
67.22 |
18.64 |
27.60 |
27.73 |
41.06 |
XI-13
14. Pollution Prevention
- 1 Pollution prevention is any technique that reduces or eliminates the quantity or toxicity of waste at the point of generation. It is the environmental management tool preferred over waste disposal or recycling. When feasible, laboratory staff should use a pollution prevention technique such as preparation of the smallest practical volumes of reagents, standards and media or downsizing of the test units in a method.
- 2 The laboratory staff should also review the procurement and use of equipment and supplies for other ways to reduce waste and prevent pollution. Recycling should be considered whenever practical.
- Waste Management – The Environmental Protection Agency requires that laboratory waste management practices be conducted consistent with all applicable rules and regulations. The Agency urges laboratories to protect the air, water and land by minimiz- ing and controlling releases from hoods and bench operations, complying with the letter and spirit of sewer discharge permits and regulations and by complying with solid and hazardous waste regulations, particularly the hazardous waste identification rules and land disposal restrictions.
- Key Words – Clostridium, Clostridium perfringens, anaerobic bacteria, spore-forming bacteria, indicator organisms, pollution, water quality.
17. References:
- Armon, R. and P. Payment, 1988. A modified mCP Medium for enumerating
Clostridium perfringens from Water Samples. Can. J. Microbiol. 34: 78-79.
- Bisson, J.W., and V.J. Cabelli, 1979. membrane filter enumeration method for
Clostridium perfringens, Appl. Environ. Microbiol. 37:55-66.
- St. John, W.D., J.R. Matches, and M.M. Wekell, 1982. Use of iron milk medium for enumeration of Clostridium perfringens. J. Assoc. Off. Anal. Chem. 65:1129-1133.
- Brenner, K. and C. Rankin, 1990. New Screening Test to Determine the Acceptabil- ity of 0.45 µm Membrane Filters of Analysis of Water, Appl. Environ. Microbiol., 56:54-64.
- Reagent Chemicals, American Chemical Society Specifications, American Chemical Society, Washington, DC. For suggestions on testing reagents not listed by the American Chemical Society, see Analar Standards for Laboratory Chemicals, BDH LTD, Poole, Dorset, U.K. and the United States Pharmacopeia.
XI-14
- American Society for Testing and Materials, Annual Book of ASTM Standards, Vol.
11.01. ASTM, Philadelphia, PA 19103-1187.
- FDA Bacteriological Analytical Manual, 7th Ed., AOAC International, Arlington, VA, 1992, Iron Milk Medium (modified), 476-477.
- Bordner, R.H., J.A. Winter and P.V. Scarpino (eds.), 1978. Microbiological Meth- ods for Monitoring the Environment, Water and Wastes, EPA-600/8-78-017, U.S. Environmental Monitoring and Support Laboratory, Cincinnati, Ohio, 5-31 or Bordner, R., 1985. Quality Assurance for Microbiological Analyses of Water. in: Quality Assurance for Environmental Measurements . ASTM STP 867, Ameri- can Society for Testing and Materials, Philadelphia, PA, pp. 133-143.5
- Standard Methods for the Examination of Water and Wastewater, 18th ed. 1992. APHA, Washington, D.C., 1992, Sections 9060A and 9060B.
- Fujioka, R.S. and Shizumura, L.K. 1985. Clostridium perfringens, A Reliable Indicator of Stream Water Quality, JWPCF, 57:986-992.
XI-15
APPENDIX A. VERIFICATION OF STATE CERTIFICATION
Please complete the following: Laboratory Name:
Address:
City: State: Zip: Contact Person:
Telephone: ( )
Laboratory Type: Utility: Commercial: State: Other:
Certification: The information requested in this section is necessary to verify the Drinking Water Laboratory certifications listed below. Please fill-out completely and supply all requested documentation.
ANALYTICAL METHODS PERFORMED |
(Indicate Methods Performed with a ) |
STATE(S)
in Which Certified |
CERTIFICATION |
Type |
Certification Date |
TC-MF |
|
|
|
|
TC-MTF |
|
|
|
|
FC-MF |
|
|
|
|
FC-MTF |
|
|
|
|
EC + MUG |
|
|
|
|
ONPG – MUG |
|
|
|
|
NA + MUG |
|
|
|
|
Please attach a copy of your current letter(s) or certificate(s) of approval for conducting the above analyses and return to:
ICR Laboratory Coordinator
U.S. EPA, OGWDW Technical Support Division
26 West Martin Luther King Drive Cincinnati, Ohio 45268
ApA-1
APPENDIX B. APPLICATION FOR LABORATORY APPROVAL FOR THE INFORMATION COLLECTION RULE (ICR)
The U.S. Environmental Protection Agency (EPA) is proposing to require public water systems which serve 10,000 people or greater to generate and provide the Agency with specific monitoring data and other information characterizing their systems. Depending on the population served, systems which use surface water, or ground water under the direct influence of surface water, would be required to monitor their source water at the intake of each plant for two disease-causing protozoa, Giardia and Cryptosporidium, total coliforms and fecal coliforms or Escherichia coli. Systems which serve more than 100,000 people would be required to monitor their source water at the intake of each plant for the microorganisms indicated above, plus total culturable viruses. When pathogen levels equal or exceed one virus or protozoan per liter in the source water, systems would also be required to monitor their finished waters for these microorganisms.
Laboratories monitoring for protozoa and viruses would have to be approved by the U.S. EPA. The attached information describes the minimal requirements for approval to perform protozoan and/or virus analyses under the Information Collection Rule. Accepted applicants will also be required to demonstrate capabilities based on analyses of unknown samples and an on-site inspection of their facility.
Those interested in being approved must first demonstrate their qualifications by complet- ing the attached application(s) and forwarding it (them) to:
ICR Laboratory Coordinator
U.S. Environmental Protection Agency Office of Ground Water and Drinking Water
Technical Support Division
26 West Martin Luther King Drive Cincinnati, Ohio 45268
Qualified applicants will be provided a copy of the ICR Microbial Laboratory Manual
describing fully the approval requirements.
Since total coliform and fecal coliform/E. coli analyses proposed under the ICR are required under the Drinking Water Laboratory Certification Program, laboratory approval for these analyses is not required under the ICR if State certification can be verified (see Appen- dix A).
ApB-1
MINIMAL REQUIREMENTS FOR VIRUS LABORATORIES
Background Information:
For ICR approval, the virus analytical laboratories must have suitable facilities, equip- ment, instrumentation, and an ongoing quality assurance (QA) program. Analysts must be experienced in viral analyses and meet performance evaluation criteria. As laboratories are approved, the U.S. EPA will provide an updated list of those laboratories with Agency approved analysts to the public water systems that serve a population of 100,000 or more.
Analytical Methods:
The proposed virus protocol was published in the Federal Register, Vol. 59, No. 28, February 10, 1994, 40 CFR Part 141 Monitoring Requirements For Public Drinking Water Supplies; Proposed Rule; pp. 6430-6444. The final draft method will be provided to those applicants that meet the minimal requirements set forth in this document. The final method will be available at the time the ICR is promulgated.
Sample Collection:
Each analytical laboratory will be responsible for procuring, assembling, sterilizing, and transporting the sample collection apparatus to the water system. Systems will be advised on proper collection techniques by the analytical laboratory in accordance with the procedures in the ICR virus protocol. A virus sampling video will be available to the system to reinforce instructions received from the analytical laboratory.
Approval of an Analytical Laboratory:
The minimal requirements for personnel (education; training or equivalent experience), facilities, equipment and instrumentation, QA/quality control (QC), etc. listed below must be met and documented in the application before the laboratory and analysts will be judged qualified to be considered for approval. If the above criteria are met, ICR approval to perform analyses will require: 1) successful performance on QC samples, as defined in the virus protocol, 2) satisfactory analyses on unknown performance evaluation (PE) samples, and 3) an on-site evaluation of the laboratory and the analyst(s).
QC Samples/Cell Line:
EPA will provide QC samples containing known virus concentrations to laboratories meeting minimal requirements. These samples are to be used initially and periodically thereafter to demonstrate the analyst(s)’ ability to process and analyze samples correctly. Buffalo green monkey (BGM) cells will be provided to establish uniform cell cultures in all laboratories.
ApB-2
Minimal Requirements:
- Personnel:
Principal Analyst/Supervisor : To be qualified for approval, a laboratory must have a principal analyst who may also serve as a supervisor if an additional analyst(s) is to be involved. The principal analyst/supervisor oversees or performs the entire analyses and carries out QC performance checks on technicians and/or other analyst(s). This person must be an experienced microbiologist with at least a B.A./B.S. degree in microbiology or a closely related field and a minimum of three years continuous bench experience in cell culture propagation, processing of virus samples, and animal virus analyses. This analyst must have analyzed a PE sample set using the ICR virus method and results must fall within acceptance limits. Also, the principal analyst must demonstrate acceptable performance during an on-site evaluation by U.S. EPA personnel.
Analyst: This person(s) performs at the bench level under the supervision of a principal analyst and can be involved in all aspects of analysis, including preparation of sampling equipment, filter extraction, sample processing, cell culture, virus assay, and data handling. The analyst must have two years of college lecture and laboratory course work in microbiology or a closely related field. The analyst must have at least six months bench experience in cell culture and animal virus analyses, including three months experience in filter extraction of virus samples and sample processing. Six months of additional bench experience in the above areas may be substituted for the two years of college. Each analyst must have analyzed a PE sample set using the ICR virus method and results must fall within acceptance limits. The analyst must also demonstrate acceptable performance during an on-site evaluation.
Technician: This person extracts filters and processes the samples under the supervision of an analyst, but does not perform cell culture work, virus detection or enumeration. The technician must have at least three months experience in filter extrac- tion and processing of virus samples.
- Laboratory Facilities: Laboratories must have an air system regulated for temperature, humidity and air cleanliness. Laboratories should be maintained under negative air pressure to protect against accidental release of viral pathogens and should be equipped with ultraviolet lights for decontamination of rooms during periods when personnel are absent. Laboratories should maintain separate rooms for preparing cell cultures and processing virus samples. However, in the absence of separate rooms, laminar flow hoods must be used for cell culture preparation to prevent contamination. Freezers, incubators, and other large instruments should be in rooms where they can be accessed without disturbing ongoing laboratory efforts. The area provided for preparation and sterilization of media, glassware, and equipment should be separate from other laboratory work areas, but close enough for convenience. Visitors and through traffic must be minimized in work areas. ICR samples will be archived for future
ApB-3
testing by polymerase chain reaction (PCR) methods which are sensitive to contamination. Therefore, rooms for processing and assaying ICR samples must not have been used for analyzing PCR products. For ICR studies, the minimal area recommended for each worker is six to ten linear feet of usable bench space per analyst, exclusive of areas requiring specialized equipment or used for preparatory and supportive activities. Bench tops should be stainless steel, epoxy plastic, or other smooth impervious material that is inert and corrosion-resistant. Laboratory lighting should be even, screened to reduce glare, and provide about 100 foot- candles of light intensity on working surfaces.
High standards of cleanliness must be maintained in work areas. Laboratory bench surface cleanliness and laboratory air quality must be monitored. The laboratory must have a pest control program that includes preventive measures such as general cleanliness and prompt disposal of waste materials. The laboratory must be in compliance with all applicable judicial ordinances and laws for the managing and disposal of pathogenic agents.
- Laboratory Equipment And Instrumentation: The laboratory must be equipped on- site with the instrumentation and equipment needed to perform the virus sample collection, extraction, concentration and assay as set forth in the ICR virus protocol. Included are incubators, water baths, hot air sterilizing ovens, autoclaves, refrigerators with -20 C freezer compartment, -70 C deep freezers, reagent grade water supply, balances, pH meter, centri- fuges, temperature recording devices, and both upright and inverted microscopes. Laminar flow hoods and UV lights are strongly recommended as added equipment within the analytical laboratory.
- Safety: Laboratory must meet Biosafety Level 2 Criteria as described in Biosafety in Microbiological and Biomedical Laboratories, 3rd Ed., HHS Publication No. (CDC) 93- 8395. U.S. Government Printing Office, May, 1993. Immunocompromised individuals must not work in or be admitted to this area .
- QA/QC Procedures: A formal QA document must be prepared and should follow the guidelines for a laboratory QA Plan, p. 7 in the Manual for the Certification of Laboratories Analyzing Drinking Water, 1990, U. S. Environmental Protection Agency Publication No. EPA/570/9-90/008, 3rd Ed., Washington, D.C., and Section II of this Manual. Laboratories must have a written QA program that applies practices necessary to minimize errors in laboratory operations that are attributable to personnel, equipment, supplies, processing procedures, or analytical methods. These include records of routine monitoring of equipment and instrumentation performance. Records of QC checks must be available to the U.S. EPA for inspection. The procedures for preparation of reagents and cell cultures and performance of the method must be followed exactly as written in the U.S. EPA ICR virus method. Reagents must be stored no longer than the designated shelf life.
- Record-Keeping And Data Reporting: A record system must be in use for tracking the samples from sample collection through log-in, analyses and data reporting.
ApB-4
INFORMATION COLLECTION RULE
APPLICATION FOR APPROVAL OF VIRUS LABORATORIES AND ANALYSTS 1
Laboratory: Address:
City: State: Zip: Contact Person:
Title:
Telephone: ( ) Fax: ( )
Type of Laboratory: Commercial Utility State Academic
Other (describe)
Principal Customers: Environmental Clinical Other
Type of Virus analyses: Human Animal Bacterial Other (describe)
PERSONNEL QUALIFICATIONS
Name, education, virus analysis experience and field in which acquired (water, waste- water, soils/sludge, shellfish, clinical, etc.)
Principal Analyst/Supervisor: Education [University/Degree(s)]: Experience:
1Where additional pages are required, clearly mark them using the same headings as in this application form.
ApB-5
Analyst #1: Education: Experience:
Analyst #2: Education: Experience:
Analyst #3: Education: Experience:
Technician #1: Education: Experience:
Technician #2: Education: Experience:
Technician #3: Education: Experience:
ApB-6
ON-SITE LABORATORY EQUIPMENT AND INSTRUMENTATION
ITEM |
Ona Order |
Number |
TYPE/MODEL |
Reagent Water System |
|
|
|
Sterilizing Oven |
|
|
|
Incubator |
|
|
|
Centrifuge |
|
|
|
pH Meter |
|
|
|
Temperature Recorder |
|
|
|
Inverted Microscope |
|
|
|
Upright Microscope |
|
|
|
Autoclave |
|
|
|
-70 C Freezer |
|
|
|
Refrigerator |
|
|
|
Analytical Balance |
|
|
|
UV Light System |
|
|
|
Water Bath |
|
|
|
Other(s) (describe) |
|
|
|
aPlace a ” ” in the “On Order” column next to items that are on order. |
CURRENT LABORATORY PROGRAMS
Virus Method(s) (processing, assay) |
Number of Analyses Per Year Per Meth- od and Virus Groups Analyzed |
|
|
|
|
|
|
ApB-7
Sample Types (Matrices Tested):
Cell Culture (Mammalian):
Documented Laboratory QA Plan: Yes No
Laboratory is in compliance with state and local ordinances and laws for handling and disposal of pathogenic agents:
Yes No
Comments:
Estimated number of water samples that can be analyzed for virus/month using the method:
The above application information is complete and accurate to the best of my knowl- edge.
Laboratory Manager or Designee
Submit Application to: ICR Laboratory Coordinator
- S. Environmental Protection Agency Office of Ground Water and Drinking Water Technical Support Division
26 West Martin Luther King Drive Cincinnati, OH 45268
ApB-8
MINIMAL REQUIREMENTS FOR PROTOZOAN LABORATORIES
Background Information:
For ICR approval, the protozoan analytical laboratories must have suitable facilities, equipment, instrumentation, and an ongoing quality assurance (QA) program. Analysts must be experienced in protozoan analyses and meet performance evaluation criteria. As laborato- ries are approved, the U.S. EPA will provide an updated list of those laboratories with Agency approved analysts to the public water systems that serve a population of 10,000 or more.
Analytical Methods:
The proposed protozoan method was published in the Federal Register, Vol. 59, No. 28, February 10, 1994, 40 CFR Part 141 Monitoring Requirements For Public Drinking Water Supplies; Proposed Rule; pp. 6416-6429. The final draft method will be provided to those applicants that meet the minimum requirements set forth in this document. The final method will be available at the time the ICR is promulgated.
Sample Collection:
Analytical laboratories will be responsible for procuring, assembling, and transporting the sample collection apparatus to the water system. Systems will be advised on proper collection techniques by the analytical laboratory in accordance with the procedures described in the protozoan protocol. A sampling video will be available to the systems to reinforce instructions received from the analytical laboratory.
Approval of the Analytical Laboratory:
The minimal requirements for personnel (education; training or equivalent experience), facilities, instruments, QA/QC, etc. listed below must be met and documented in this applica- tion before laboratories and analyst(s) will be judged qualified to be considered for approval. If the above criteria are met, ICR approval to perform analyses also will require: 1) recovery of both Giardia cysts and Cryptosporidium oocysts from QC samples, 2) satisfactory analyses on unknown PE samples and 3) an on-site evaluation of the laboratory and the analyst(s).
QC Samples:
The U.S. EPA will provide QC samples containing known Giardia and Cryptosporidium concentrations to laboratories meeting minimal requirements. These samples are to be used initially and periodically thereafter to demonstrate the analyst(s)’ ability to process and analyze samples correctly.
ApB-9
Minimal Requirements:
- Personnel:
Principal Analyst/Supervisor : To be qualified for approval, a laboratory must have a principal analyst who may also serve as a supervisor if an additional analyst(s) is to be involved. The principal analyst/supervisor oversees or performs the entire analyses and carries out QC performance checks on technicians and/or other analysts. The principal analyst/supervisor must confirm all protozoan internal structures demonstrated at the microscope by subordinates. This person must be an experienced microbiologist with at least a B.A./B.S. degree in microbiology or a closely related field. The principal analyst also must have at least one year of continuous bench experience with immunofluorescent antibody (IFA) techniques and microscopic identification and have analyzed at least 100 water and/or wastewater samples for Giardia and/or Cryptosporidium. In addition, PE samples must be analyzed using the ICR protozoan method and results must fall within acceptance limits. The principal analyst/supervisor must also demonstrate acceptable performance during an on-site evaluation.
Analyst: This person(s) performs at the bench level under the supervision of a principal analyst/supervisor and is involved in all aspects of the analysis, including preparation of sampling equipment, filter extraction, sample processing, microscopic protozoan identification, and data handling. Recording presence or absence of morpho- logical characteristics may be done by the analyst but must be confirmed by the principal analyst. The analyst must have two years of college lecture and laboratory course work in microbiology or a closely related field. The analyst also must have at least six months bench experience, must have at least three months experience with IFA techniques, and must have analyzed at least 50 water and/or wastewater samples for Giardia and/or Cryptosporidium. Six months of additional bench experience in the above areas may be substituted for two years of college. In addition, PE samples must be analyzed using the ICR protozoan method and results must fall within acceptance limits. The analyst must also demonstrate acceptable performance during an on-site evaluation.
Technician: This person extracts filters and processes the samples under the supervision of an analyst, but does not perform microscopic protozoan detection and identification. The technician must have at least three months experience in filter extraction and processing of protozoa samples.
Laboratory Facilities: The laboratory must have dedicated, well-lighted bench space commensurate with the number of samples to be analyzed. Six to ten feet of usable bench space are required per analyst, exclusive of areas requiring specialized equipment or used for preparatory and supportive activities. Bench tops should be stainless steel, epoxy plastic or other smooth impervious material that is corrosion-resistant. Laboratory lighting should be even, screened to reduce glare, and provide 100 foot-candles of light intensity on working
ApB-10
surfaces. Laboratory floor space must be sufficient for stationary equipment such as refrigera- tors and low-speed and large-capacity centrifuges. Facilities for washing and sterilization of laboratory glassware, plasticware and equipment must be present. A dedicated space that can be darkened must be available for the microscopic work. Laboratory areas should be kept free of clutter and equipment and supplies should be stored when not in use. It is strongly recom- mended that laboratories should be maintained under negative air pressure to protect against accidental release of pathogens and should be equipped with ultraviolet lights for decontamina- tion of rooms during periods when personnel are absent. High standards of cleanliness must be maintained in work areas. The laboratory must have a pest control program that includes preventive measures such as general cleanliness and prompt disposal of waste materials. The laboratory must be in compliance with all applicable judicial ordinances and laws for manage- ment and disposal of pathogenic agents.
- Laboratory Equipment And Instrumentation: The laboratory must be equipped on- site with a reagent water supply system, autoclave, refrigerator (4 C) with -20 C freezer compartment, pH meter, slide-warming tray or incubator (37 ± 3 C), balance (top loader or pan), membrane filtration equipment for epifluorescent staining, and hydrometer set. Specific requirements for the microscope include differential interference contrast (DIC) or Hoffman modulation optics (including 20X and 100X objectives). DIC or Hoffman modulation optics should have epifluorescence capability. The epifluorescence vertical illuminator should have either a 50 or 100 watt high-pressure mercury bulb with appropriate excitation and band-pass filters (exciter filter: 450-490 nm; dichroic beam-splitting mirror: 510 nm; barrier or suppres- sion filter: 515-520 nm) for examining fluorescein isothiocyanate-labeled specimens.
- Safety: The laboratory must meet Biosafety Level 2 Criteria as described in Biosafety in Microbiological and Biomedical Laboratories, 3rd Ed., HHS Publication No. (CDC) 93- 8395. U.S. Government Printing Office, May, 1993. Immunocompromised individuals must not work in or be admitted to this area .
- QA/QC Procedures: A formal QA document must be prepared and should follow the guidelines for a laboratory QA Plan, p. 7 in the Manual for the Certification of Laboratories Analyzing Drinking Water, 1990, U. S. Environmental Protection Agency Publication No. EPA/570/9-90/008, 3rd Ed., Washington, D.C., and Section II of this Manual. Laboratories must have a written QA program that applies QC practices necessary to minimize errors in laboratory operations that are attributable to personnel, equipment, supplies, processing procedures, or analytical methods. These include records of routine monitoring of equipment and instrumentation performance. Records of all QC checks must be available to the U.S. EPA for inspection. The procedures for the preparation of reagents and performance of the method must be followed exactly as written in the U.S. EPA ICR protozoan method. Reagents must be stored no longer than the designated shelf life.
- Record-Keeping And Data Reporting: A record system must be in use for tracking the samples from sample collection through log-in, analyses and data reporting.
ApB-11
INFORMATION COLLECTION RULE
APPLICATION FOR APPROVAL OF PROTOZOAN LABS AND ANALYSTS 2
Laboratory: Address:
City: State: Zip: Contact Person:
Title:
Telephone: ( ) Fax: ( )
Type of Laboratory: Commercial Utility State Academic
Other (describe)
Principal Customers: Environmental Clinical Other
Type of Protozoa Giardia Cryptosporidium Entamoeba
Analyses: Other (describe) PERSONNEL QUALIFICATIONS
Name, education, protozoan analysis experience and field in which acquired (water,
wastewater, clinical, etc.) Principal Analyst/Supervisor:
Education [University/Degree(s)]: Experience:
2Where additional pages are required, clearly mark them using the same headings as in this application form.
ApB-12
Analyst #1: Education: Experience:
Analyst #2: Education: Experience:
Analyst #3: Education: Experience:
Technician #1: Education: Experience:
Technician #2: Education: Experience:
Technician #3: Education: Experience:
ApB-13
ON-SITE LABORATORY EQUIPMENT AND INSTRUMENTATION
ITEM |
On Order |
Number |
TYPE/MODEL |
Autoclave |
|
|
|
Refrigerator |
|
|
|
Freezer |
|
|
|
pH Meter |
|
|
|
Analytical Balance |
|
|
|
Top-loader Balance |
|
|
|
Membrane Filtration Equip- ment (for epifluorescent staining) |
|
|
|
Hydrometer Set |
|
|
|
Reagent Grade Water Supply |
|
|
|
Slide Warmer |
|
|
|
Incubator |
|
|
|
Centrifuge |
|
|
|
Centrifuge Rotors |
|
|
|
Other(s) (describe) |
|
|
|
Place a ” in the “On Order” column next to items that are on order. |
ApB-14
MICROSCOPE CAPABILITY
Vendor Name: |
|
|
Model: |
|
|
Optical Capability:
Epifluorescence |
Yes |
|
|
No |
DIC |
Yes |
|
|
No |
|
|
Hoffman Modulation |
Yes |
|
|
No |
|
|
Mercury Lamp watt bulb
FITC Cube Specs. nm exciter filter;
nm beam splitting dichroic mirror; or nm barrier or suppression filter
Objective Power |
Type (Achromate, Neofluor,
oil, etc.) |
Numerical Aperture |
Used with (Epifluor, D.I.C., etc.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CURRENT LABORATORY PROGRAMS
Protozoan Method(s) |
Number of Analyses Per Year Per Method |
|
|
|
|
|
|
ApB-15
Sample Types (Matrices Tested):
Documented Laboratory QA Plan: Yes No
Laboratory is in compliance with state and local ordinances and laws for handling and disposal of pathogenic agents:
Yes No
Comments:
Estimated number of water samples that can be analyzed for protozoa/month using the ICR method:
The above application information is complete and accurate to the best of my knowl- edge.
Laboratory Manager or Designee
Submit Application to: ICR Laboratory Coordinator
- S. Environmental Protection Agency Office of Ground Water and Drinking Water Technical Support Division
26 West Martin Luther King Drive Cincinnati, OH 45268
ApB-16
APPENDIX C. CHECKLIST FOR LABORATORY APPROVAL FOR
GIARDIA AND CRYPTOSPORIDIUM
ApC-1
ICR Protozoan Laboratory Checklist |
Laboratory: |
Address: |
City: |
State: |
Zip: |
Type of Laboratory (Check): |
Commercial: |
Utility: |
State: |
Academic: |
Other (Describe): |
Principal Customers: (Check) |
Environmental: Clinical: Other (Describe): |
Type of Protozoan Analyses:
(Check each) |
Giardia: |
Cryptosporidium: |
Entamoeba: |
Other (describe): |
Laboratory Contact Person: |
Title: |
Telephone: |
Fax: |
Principal Analyst/Supervisor Name: |
Analyst Name: |
Name of Person Being Evaluated: |
Laboratory Evaluated by: |
Date: |
ApC-2
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Are the personnel listed on the ICR approval application still with the laboratory? |
|
|
Are there any personnel in the laboratory not listed on the ICR approval application? |
|
|
Is the documentation available showing that the principal analyst/super- visor has analyzed 100 water and/or wastewater samples for Giardia and/or Cryptosporidium? |
|
|
Is the documentation available showing that the analyst has analyzed 50 water and/or wastewater samples for Giardia and/or Cryptosporidium? |
|
|
Is the laboratory well lighted (approximately 100 foot-candles of light intensity on work surfaces)? |
|
|
Are 6-10 ft of bench space available per analyst? |
|
|
Are the bench tops made of a smooth, impervious surface? |
|
|
Is the laboratory floor space sufficient for the stationary equipment? |
|
|
Is glassware washing equipment available? |
|
|
Is the laboratory neatly organized with unused equipment and supplies being stored (free of clutter)? |
|
|
Are high standards of cleanliness and prompt disposal of waste materials exhibited? |
|
|
Is the laboratory equipped with ultraviolet lights and under negative air pressure? |
|
|
Does the laboratory have a reagent grade water system? |
|
|
Does the laboratory have an autoclave? |
|
|
Does the laboratory have a refrigerator (4 C) with a -20 C freezer compartment? |
|
|
Does the laboratory have a pH meter associated with two or three calibra- tion buffers? |
|
|
Does the laboratory have either an incubator or slide warming table calibrated to 37 ± 3 C? |
|
|
ApC-3
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Does the laboratory have either a top loader or pan balance associated with calibration weights? |
|
|
Does the laboratory have a properly maintained and adjusted stomacher? |
|
|
Does the laboratory have a Hoefer filtration manifold, model FH 255V? |
|
|
Are the well weights for the Hoefer manifold well maintained? |
|
|
Are the microscope slides the appropriate size? |
|
|
Is the laboratory using clear nail polish to seal the coverslips to the slides? |
|
|
Are the cover slips 25 mm2 and No. 1½? |
|
|
Does the laboratory have a hydrometer set covering the range 1.0-2.0? |
|
|
Does the laboratory have an epifluorescent microscope equipped with either Hoffman modulation or differential interference contrast optics? |
|
|
Is the microscope easily changed from epifluorescent optics to either Hoffman modulation or differential interference contrast optics and vice versa? |
|
|
Does the laboratory have a 20X scanning objective with a numerical aperture of 0.6 on the microscope? |
|
|
Is the microscope equipped with an ocular micrometer or some other measuring device? |
|
|
Has the ocular micrometer been calibrated in conjunction with the 20X and the 100X objectives? |
|
|
Is a table of objective calibrations near the microscope? |
|
|
Does the laboratory have a stage micrometer? |
|
|
Does the laboratory have a 100X objective with a numerical aperture of
1.3 on the microscope? |
|
|
ApC-4
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Is the epifluorescent portion of the microscope equipped with an appro- priate excitation and band pass filters for examining fluorescein isothiocyanate-labeled specimens (exciter filter: 450-490 nm; dichroic beamsplitting mirror 510 nm; barrier or suppression filter: 515-520 nm)? |
|
|
Is the mercury bulb in the epifluorescent lamp house either a 50 or a 100 watt bulb? |
|
|
Does the laboratory keep a log or have an hour totalizer on the trans- former of the number of hours on the mercury bulb? |
|
|
Has the mercury bulb been used longer than 100 h in the case of 50 watt bulb or longer than 200 h in the case of a 100 watt bulb? |
|
|
Can the principal analyst/supervisor establish Köhler illumination on the microscope? |
|
|
Can the analyst establish Köhler illumination on the microscope? |
|
|
Can the principal analyst/supervisor focus both microscope eyepieces? |
|
|
Can the analyst focus both microscope eyepieces? |
|
|
Did the principal analyst/supervisor adjust the interpupillary distance? |
|
|
Did the analyst adjust the interpupillary distance? |
|
|
Does the laboratory have a large capacity centrifuge? |
|
|
Does the laboratory have a swinging bucket rotor capable of spinning 250 ml capacity or greater screw-cap conical bottles? |
|
|
Does the laboratory have a swinging bucket rotor capable of spinning 50 ml capacity conical screw-cap tubes? |
|
|
Does the laboratory have a formal QA laboratory plan prepared and ready for examination? |
|
|
Does the laboratory have records of all QC checks available for inspec- tion? |
|
|
Does the laboratory have an adequate record system for tracking sam- ples from collection through log-in, analysis and data reporting? |
|
|
ApC-5
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Is a positive and a negative Quality Control filter run with each week’s batch of filters being analyzed? |
|
|
Is the laboratory using Commercial filters with Commercial LT-10 filter holders or Filterite filters with Filterite filter holders? |
|
|
Are the sampling filters 10 in (25.4 cm) long and 1 m in nominal porosity? |
|
|
Is the sampling apparatus configured appropriately for raw water sam- pling? |
|
|
Is the sampling apparatus configured appropriately for finished water sampling? |
|
|
Is the sampling apparatus cleaned well before reshipment and/or use? |
|
|
Does the laboratory have a checklist or set of sampling instructions which are used, when sampling is done by someone other than labora- tory personnel? |
|
|
Are reagents well labelled with preparation dates and who prepared the reagent? |
|
|
Does the laboratory have formulation or recipe cards for the preparation of 2.0% sodium thiosulfate, 10% neutral buffered formalin, phosphate buffered saline, 1% sodium dodecyl sulfate solution, 1% Tween 80 solution, elution solution, 2.5 M sucrose solution, Percoll-sucrose solution, the ethanol/glycerin dehydration series, DABCO-glycerin mounting medium, and 1% bovine serum albumin? |
|
|
Is the laboratory using Ensys’s hydrofluor-combo kit for staining Giar- dia cysts and Cryptosporidium oocysts? |
|
|
Is the Ensys hydrofluor-combo kit still within the expiration time set by the manufacturer? |
|
|
Is the Percoll-sucrose solution used within a week of preparation? |
|
|
Is the elution solution used within a week of preparation? |
|
|
Is the DABCO-glycerin mounting medium discarded six months after preparation? |
|
|
ApC-6
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Is the 1% bovine serum albumin discarded six months after preparation? |
|
|
Are disposable cutting tools used to cut the sampling filter down to the core? |
|
|
Are the disposable cutting tool blades reused? |
|
|
Is the sampling filter in either a glass or stainless steel pan of the appro- priate size, while it is being cut to the core? |
|
|
Are the filter fibers divided appropriately before hand washing? |
|
|
Is the total hand washing time a minimum of 30 min? |
|
|
Is stomacher washing done in two five minute intervals with redistri- bution of the filter fibers between the intervals? |
|
|
Is the right amount of 10% neutral buffered formalin added to the concentrated particulates at the appropriate time? |
|
|
Are the concentrated particulates diluted appropriately before the Percoll-sucrose flotation? |
|
|
Is the Percoll-sucrose gradient prepared correctly in a clear conical centrifuge tube? |
|
|
Is a centrifugation nomograph for determining relative centrifugal force (gravities) located close to the centrifuge(s)? |
|
|
Is the Percoll-sucrose gradient centrifuged correctly with slow accelera- tion and deceleration? |
|
|
Is the Percoll-sucrose gradient interface harvested appropriately after centrifugation? |
|
|
Is the final volume of the interface 5 ml, when harvesting is complete? |
|
|
Are 5-mm diameter 12-well red teflon heavy coated slides used to determine the correct sample volume per filter in the IFA staining procedure? |
|
|
Is the sample volume per filter in the IFA staining procedure done correctly? |
|
|
ApC-7
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Are support and Sartorius membranes handled with blunt end forceps initially? |
|
|
Are the support and Sartorius membranes properly hydrated before application to the manifold? |
|
|
Is the Hoefer manifold properly configured and adjusted before the addition of the support and Sartorius membranes? |
|
|
Do the Sartorius membrane filters the laboratory is using have a porosity between 0.2 and 1.2 m? |
|
|
Is a positive and a negative IFA Control using a Sartorius filter run with each run of the manifold? |
|
|
Are the Hoefer manifold wells labelled well during the staining proce- dure? |
|
|
Does the sample application to the membranes on the manifold include rinses of the wells and membranes with 1% bovine serum albumin before and after application? |
|
|
Is the primary antibody diluted correctly with 1X phosphate buffered saline and goat serum? |
|
|
Is the right amount of primary antibody applied per membrane, and is it incubated for the correct amount of time? |
|
|
Is the primary antibody rinsed away correctly before the application of the secondary antibody? |
|
|
Is the secondary antibody diluted correctly? |
|
|
Is the right amount of secondary antibody applied per membrane, and is it incubated for the correct amount of time? |
|
|
Are the Hoefer manifold well weights covered with aluminum foil during the secondary antibody incubation? |
|
|
Is the secondary antibody rinsed away correctly after the incubation period? |
|
|
Is the alcohol dehydration step done correctly? |
|
|
ApC-8
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Are the glass slides that are to receive the membranes from the manifold labelled in advance? |
|
|
Have the labelled glass slides been prewarmed for 20-30 min with 75 L of 2% DABCO-glycerin before the application of the membrane? |
|
|
Is a fresh, clean pair of forceps used to transfer each membrane from the Hoefer manifold to its respective glass slide? |
|
|
Is care exercised to insure that the Sartorius membranes are applied top side up to the slide? |
|
|
Are the membranes allowed to clear before application of the cover slip? |
|
|
Are the membranes flattened correctly, before sealing the cover slip? |
|
|
Are all the edges of the cover slip sealed well with clear nail polish? |
|
|
Is sample processing data being recorded as the method is being per- formed? |
|
|
Are the finished slides stored in an appropriate “dry-box”? |
|
|
Is the dry-box of slides allowed to reach room temperature before being opened? |
|
|
Is the microscope aligned and adjusted before the analysts starts scan- ning and reading slides? |
|
|
Is the scanning of the slides done appropriately, with the entire coverslip being scanned rather than just the membrane? |
|
|
Are measurements done with the 100X objective? |
|
|
Is the room in which the microscope is located darkened while the microscope is being used? |
|
|
Are the positive and negative control slides examined as prescribed in the method, including the complete examination of 3 Giardia cysts and 3 Cryptosporidium oocysts? |
|
|
Can the microscopist who is reading the sample slides easily change the optics from epifluorescence to Hoffman modulation or differential interference contrast optics? |
|
|
ApC-9
ICR Protozoan Laboratory Checklist |
Question |
Answer |
Yes |
No |
Are confirmations of internal structures within Giardia cysts and Cryptosporidium oocysts being confirmed by a principal analyst/su- pervisor. |
|
|
Is the microscopic data being entered onto the Giardia and Crypto- sporidium report forms appropriately? |
|
|
Are the results from each sample being calculated on the provided computer spreadsheet? |
|
|
Are the computer spreadsheet files backed up on more than one disk, to insure data are not lost in the eventuality of some hardware failure? |
|
|
Are the Hoefer manifold and the stainless steel wells cleaned as pre- scribed in the method? |
|
|
Are the forceps used during the IFA staining cleaned well between uses? |
|
|
Is all glassware and plasticware washed well and stored appropriately between uses? |
|
|
ApC-10
ICR Protozoan Laboratory Checklist |
Comments: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ApC-11
APPENDIX D. CHECKLIST FOR LABORATORY APPROVAL FOR TOTAL CULTURABLE VIRUS
ApD-1
SECTION I – LABORATORY-SPECIFIC INFORMATION
ICR Virus Laboratory Checklist |
Laboratory: |
Address: |
City: |
State: |
Zip: |
Type of Laboratory (Check): |
Commercial: |
University: |
Utility: |
State: |
Other (Describe): |
Principal Custom- ers: (Check) |
Environmental: Clinical: Other (Describe): |
Laboratory Contact Person: |
Title: |
Telephone: |
Fax: |
Laboratory Evaluated by: |
Date: |
|
|
|
|
ApD-2
1. Qualifications of Laboratory Personnel |
Name |
Position/Title |
ICR
Position |
To Be Evaluated (Y/N) |
Time in Present Position |
Academic Training/ Degree |
Job Training/ Experience/ Area |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Codes for Marking Checklist
S – Satisfactory U – Unsatisfactory NA- Not Applicable
Item to be evaluated |
Evaluation |
2. Laboratory Facilities |
2.1 Laboratory rooms are clean, and temperature and humidity con- trolled |
|
2.2 Lighting at bench top is adequate |
|
2.3 Bench tops have smooth, impervious surfaces |
|
2.4 Working space per analyst is adequate |
|
2.5 Storage space is adequate |
|
2.6 Work is separated by room or by microbiological hoods |
|
3. Laboratory Safety |
3.1 Laboratory meets and follows “laboratory biosafety level 2 guide- lines” |
|
3.2 Access to laboratory is limited |
|
3.3 Lab coats are used in the laboratory |
|
3.4 Mechanical pipetting devices are used |
|
3.5 Food is not stored or consumed in the laboratory |
|
3.6 Appropriate biohazard signs are placed on laboratory access doors |
|
3.7 A written biosafety manual is followed and available for inspection |
|
3.8 Laboratory personnel are adequately trained |
|
3.9 Laboratory has provision for disposal of microbiological wastes |
|
4. Laboratory Equipment and Supplies |
4.1 Laboratory pH Meter |
|
Manufacturer |
Model |
4.1.1 Accuracy ± 0.1 units; scale graduations, 0.1 units |
|
4.1.2 pH buffer solution aliquots are used only once |
|
4.1.3 Electrodes are maintained according to manufacturer’s rec- ommendations |
|
|
|
|
ApD-4
Item to be evaluated |
Evaluation |
4.1.4 Commercial buffer solutions are dated when received and discarded before expiration date |
|
QC 4.1.5 A record of pH measurements and calibrations used is maintained |
|
4.2 Light Microscope |
Manufacturer |
Model |
4.2.1 Microscope is equipped with lenses to provide about 40X – 100X total magnification |
|
4.2.2 Optical clarity is good |
|
4.3 Inverted Light Microscope |
Manufacturer |
Model |
4.3.1 Microscope is equipped with lenses to provide about 40X – 100X total magnification |
|
4.3.2 Optical clarity is good |
|
4.4 Microbiological Hood |
Manufacturer |
Model |
4.4.1 Hood is at least a class II biological safety cabinet |
|
4.4.2 Hood is certified on an annual basis |
|
4.5 Temperature Monitoring |
4.5.1 Glass/mercury, dial thermometers or continuous recording devices are used with appropriate equipment. Units are graduated in no more than 0.5 C increments. Mercury columns are not separated |
|
QC 4.5.2 Calibration of glass/mercury thermometers is checked annually and dial thermometers quarterly at the temperature used against a reference NIST thermometer or one meeting the requirements of NIST Monograph SP 250-23 |
|
QC 4.5.3 Correction data are available for reference thermometers |
|
QC 4.5.4 Continuous recording devices are recalibrated annually |
|
|
|
|
ApD-5
Item to be evaluated |
Evaluation |
4.6 Incubator |
|
Manufacturer |
Model |
4.6.1 An internal temperature of 36.5 ± 1 C is maintained |
|
4.6.2 A temperature monitoring device is placed on a shelf near area of use. The bulb or probe of the temperature monitor- ing device is in liquid |
|
QC 4.6.3 Temperature is recorded at least once per day for each workday in use |
|
4.7 Refrigerator |
Manufacturer |
Model |
4.7.1 An internal temperature of 1 to 5 C is maintained |
|
4.7.2 A temperature monitoring device is placed on a shelf near area of use. The bulb or probe of the temperature monitor- ing device is in liquid |
|
QC 4.7.3 Temperature is recorded at least once per day for each workday in use |
|
4.8 Freezer, -20 C |
Manufacturer |
Model |
4.8.1 An internal temperature of -20 ± 5 C is maintained |
|
4.8.2 A temperature monitoring device is placed on a shelf near area of use. |
|
QC 4.8.3 Temperature is recorded at least once per day for each workday in use |
|
4.9 Freezer, -70 C |
Manufacturer |
Model |
4.9.1 An internal temperature of -70 ± 3 C or lower is main- tained |
|
4.9.2 A temperature monitoring device is placed on a shelf near area of use |
|
|
|
|
ApD-6
Item to be evaluated |
Evaluation |
QC 4.9.3 Temperature is recorded at least once per day for each workday in use |
|
4.10 Refrigerated Centrifuge |
Manufacturer |
Model |
4.10.1 Operates at a centrifugal force of at least 4,000 ×g |
|
4.10.2 Holds at 4 C during centrifugation run |
|
4.10.3 Appropriate rotor holds 100 – 1000 ml bottles |
|
QC 4.10.4 A log recording rotor serial number, run speed and time, run temperature and operator’s initials is kept for each centrifugation run |
|
4.11 Balance |
Manufacturer |
Model |
QC 4.11.1 Balance is calibrated monthly |
|
QC 4.11.2 Correction data are available for S/S-1 calibration weights |
|
4.11.3 An annual service contract or internal maintenance protocol is maintained |
|
4.12 Autoclave |
Manufacturer |
Model |
4.12.1 Unit is equipped with a temperature gauge with sensor on exhaust |
|
4.12.2 Unit depressurizes slowly so that media do not boil over |
|
4.12.3 Unit’s automatic timing mechanism is adequate |
|
4.12.4 A service contract or internal maintenance protocol is maintained |
|
4.12.5 A maximum temperature-registering thermometer or heat- sensitive tape is used with each cycle |
|
QC 4.12.6 Spore strips or ampoules are used on a monthly basis |
|
QC 4.12.7 Date, contents, sterilization time and temperature are re- corded for each cycle |
|
4.13 Hot Air Oven (if used) |
Manufacturer |
Model |
|
|
|
ApD-7
Item to be evaluated |
Evaluation |
4.13.1 Hot air oven maintains temperature of 170 – 180 C for at least 2 h |
|
4.13.2 Bulb or probe of temperature monitoring device is placed in sand during use. Thermometer graduated in no more than 10 C increments |
|
QC 4.13.3 Date, sterilization time and temperature are recorded for each cycle |
|
4.14 Pump |
Manufacturer |
Model |
Pump is self-priming |
|
4.15 Polypropylene Container |
Manufacturer/Source |
Model/Cat. No. |
Container holds 40 L; contents can be mixed without spill- ing |
|
4.16 Positive Pressure Source (record for source used) |
Compressed air |
|
Compressed nitrogen |
|
Laboratory air source |
|
Manufacturer |
Model |
Peristaltic pump |
|
Manufacturer |
Model |
4.17 Magnetic Stirrer |
Manufacturer |
Model |
4.18 Source for Reagent Grade Water |
Type/Manufacturer |
Model/Cat. # |
4.18.1 Still or deionization unit is maintained according to manu- facturer’s instructions |
|
4.18.2 Reagent grade water is used to prepare all media and re- agents |
|
QC 4.18.3 The conductivity is tested with each use. Conductivity is
>0.5 megohms-cm at 25 C |
|
|
|
|
ApD-8
Item to be evaluated |
Evaluation |
5. General Laboratory Practices |
|
5.1 Analytical Media |
|
5.1.1 General |
|
5.1.1.1 Commercial media and chemicals are dated upon receipt. Only analytical reagent or ACS grade chemicals are used for preparation of media |
|
5.1.1.2 Commercial dehydrated or liquid media are used for propa- gation of tissue culture cells. Dehydrated media are pre- pared and stored as recommended by manufacturers. |
|
5.1.1.3 Commercial media and chemicals are discarded by man- ufacturers’ expiration dates. Laboratory prepared media are discarded by the expiration dates indicated in the Virus Monitoring Protocol |
|
5.1.1.4 Each lot of medium is checked for sterility before use |
|
QC 5.1.1.5 Lot numbers of commercial media and chemicals are re- corded. Date of preparation, type of medium, lot number, sterilization procedure, pH and technician’s initials are recorded for laboratory prepared media |
|
5.1.2 Thiosulfate (2%) |
Solutions are stored at or below room temperature and discarded after six months |
|
5.1.3 Hydrochloric acid |
5.1.3.1 Solutions are prepared at least 24 h prior to use in sampling or virus assays |
|
5.1.3.2 Solutions are stored at or below room temperature and discarded after six months |
|
5.1.4 Sodium Hydroxide |
5.1.4.1 Solutions are prepared at least 24 h prior to use in virus assays |
|
5.1.4.2 Solutions are stored in polypropylene containers at room temperature and discarded after 3 months |
|
5.1.5 Beef Extract (1.5%) |
5.1.5.1 Final pH is 9.5 |
|
ApD-9
Item to be evaluated |
Evaluation |
5.1.5.2 Solution is stored at 4 C and discarded after one week or at
-20 C and discarded after 18 months |
|
5.1.6 Sodium Phosphate |
5.1.6.1 Final pH is between 9.0 and 9.5 |
|
5.1.6.2 Solutions are stored at or below room temperature and discarded after six months |
|
5.1.7 Washing Solution |
5.1.7.1 Salt solution is cooled to room temperature before addition of serum |
|
5.1.7.2 Solutions are stored at 4 C and discarded after 3 months or at -20 C and discarded after 18 months |
|
5.1.8 |
Chlorine |
|
5.1.8.1 Final pH is between 6 and 7 |
|
5.1.8.2 Solutions are stored at or below room temperature and discarded after one month |
|
5.1.9 |
Iodine |
|
Solutions are stored at room temperature and discarded after six months |
|
5.2 Sterilization and Disinfection |
5.2.1 Autoclavable glassware, plasticware and equipment are autoclaved at 121 C for 1 h or, if appropriate, sterilized by dry heat at 170 C for at least 1 h |
|
5.2.2 Non-autoclavable supplies are disinfected with 0.1% chlo- rine (pH 6-7) for 30 min or in a gas sterilizer according to the manufacturer’s recommendations |
|
5.2.3 Contaminated materials are autoclaved at 121 C for at least 1 h |
|
5.2.4 Adequate glassware washing facilities are available for re- usable lab ware |
|
5.2.5 Surfaces are disinfected before and after use and after spills |
|
7. Quality Assurance |
A written QA plan is followed and available for inspection |
|
ApD-10
SECTION II – ANALYST-SPECIFIC INFORMATION (To be filled out for each principal analyst/analyst/technician seeking approval for ICR virus analysis):
Name of Analyst/Technician: |
Item to be evaluated |
Evaluation |
6. Analytical Methodology |
6.1 General |
Only the virus analytical method dated July, 1995, is used for site visit evaluation |
|
6.2 QC Samples |
A polypropylene container and pump are used to pump a negative QC sample through a 1MDS filter in a standard sampling appara- tus. All components of the system are sterile |
|
6.3 Filter Elution |
6.3.1 Residual water is blown out from the cartridge housing before addition of beef extract |
|
6.3.2 1MDS filters are slowly eluted with 1.5% beef extract twice. The flow of beef extract is interrupted for 1 min during each pass to enhance elution |
|
6.3.3 An air filter is used with a positive pressure lab air source |
|
6.4 Organic Flocculation |
QC |
6.4.1 |
The pH meter is standardized at pH 4 and 7 |
|
6.4.2 The pH electrode is disinfected before and after use |
|
6.4.3 The pH of the eluate is adjusted slowly to 3.5 ± 0.1 with 1 M HCl with stirring at a speed sufficient to develop a vor- tex |
|
6.4.4 The eluate is stirred for 30 min after pH adjustment |
|
6.4.5 The pH adjusted eluate is centrifuged at 2,500 ×g for 15 min at 4 C. |
|
6.4.6 Supernatant from centrifuge run is properly discarded |
|
|
6.4.7 |
Precipitate from centrifuge run is dissolved in 30 ml of
0.15 M sodium phosphate. |
|
QC |
6.4.8 |
The pH meter is standardized at pH 7.0 and 10.0 |
|
|
6.4.9 |
The pH electrode is disinfected before and after use |
|
ApD-11
Name of Analyst/Technician: |
Item to be evaluated |
Evaluation |
6.4.10 The pH of the dissolved precipitate is checked and read- justed to 9.0-9.5, if necessary |
|
6.4.11 The dissolved precipitate is centrifuged at 4,000-10,000 ×g
for 10 min at 4 C |
|
6.4.12 The supernatant from the 4,000-10,000 ×g run is saved and the precipitate properly discarded |
|
6.4.13 The pH of the supernatant is adjusted to 7.0-7.5 with 1 M HCl |
|
6.4.14 The supernatant is treated to remove or reduce microbial contamination. Sterilizing filters are pretreated before use with beef extract |
|
6.4.15 The final volume is recorded after treatment |
|
6.4.16 The treated supernatant is divided into subsamples. |
|
6.5 Total Culturable Virus Assay |
QC 6.5.1 |
Passage 117 to 250 BGM cells from the U.S. EPA are being cultured for ICR virus assays |
|
6.5.2 |
Cultures are used 3-6 days after passage. Cultures are washed prior to inoculation with serum free medium |
|
6.5.3 |
At least 10 replicate cultures per subsample or subsample dilution are inoculated with a proper inoculation volume |
|
6.5.4 |
Inoculation volume does not exceed 0.04 ml/cm2 |
|
6.5.5 |
An adsorption period of 80-120 min is used. Adsorption occurs at 22 to 36.5 ± 1 C |
|
6.5.6 Liquid maintenance medium is added and cultures are incubated at 36.5 ± 1 C |
|
6.5.7 A 2nd passage is performed using 10% of the medium from the 1st passage. Samples positive in the 1st passage are filtered prior to passage |
|
6.5.8 Analyst demonstrates ability to perform MPN calculations |
|
6.5.9 A positive and negative control is run with each sample |
|
ApD-12
DESCRIPTION OF CHECKLIST FOR LAB APPROVAL FOR VIRUS ANALYSIS
Note: Written records must be retained for five years for quality control items designated as “QC”.
1. Personnel
1.1 Principal Analyst/Supervisor
The principal analyst/supervisor is a qualified microbiologist with experience with environ- mental virology. The principal analyst/supervisor oversees all analyses of samples for viruses.
- 1.1 Academic Training: Minimum of a bachelor’s degree in the life sciences.
- 1.2 Job Training: Minimum of three years experience in cell culture and animal virus analyses.
1.2 Analyst
The analyst performs at the bench level with minimal supervision and is involved in all aspects of the analysis, including sample collection, filter extraction, sample processing and assay.
- 2.1 Academic Training: Minimum of two years of full time college with a major in life science.
- 2.2 Job Training: Minimum of six months of full-time bench experience in cell culture and animal virus analyses.
1.3 Technician
The technician extracts the filter and processes samples, but does not perform tissue culture work.
- 3.1 Academic Training: No requirements.
- 3.2 Job Training: Three months experience in filter extraction of virus samples and sample processing.
2. Laboratory Facilities
- 1 Laboratory facilities are temperature and humidity controlled. Laboratories are clean; a pest control program is in place, if appropriate.
- 2 Work surfaces have adequate lighting (minimum of 100 foot-candles).
- 3 Laboratory bench tops have smooth, impervious surfaces.
ApD-13
- 4 There is at least six to ten linear feet of usable bench space per analyst with a minimum of 36-38 inches of depth.
- 5 There is sufficient laboratory space for storage of media, glassware and equipment.
- 6 Filter extraction/sample processing is performed in a separate laboratory room from cell culture and virus work. Cell culture and virus work are performed in separate rooms or in separate microbiological hoods. A program is in place to ensure that no cross-contamination occurs if the latter is used.
3. Laboratory Safety
- 1 The laboratory meets and follows laboratory biosafety level 2 guidelines.
- 2 Laboratories have limited access.
- 3 Lab coats are worn while working in laboratories.
- 4 Mouth pipetting is not allowed in the laboratory.
- 5 Food and drinks are not stored or consumed in the laboratory.
- 6 Biohazard signs identifying biohazards are placed on the laboratory access doors.
- 7 A written biosafety manual is followed and available for inspection.
- 8 Laboratory personnel have been given laboratory safety training.
- 9 The laboratory is in compliance with all applicable judicial ordinances and laws for virus work and biological waste disposal.
4. Laboratory Equipment and Supplies
- 1.1 The accuracy and scale graduations of a laboratory pH meter are within ±0.1 pH units. The accuracy and scale graduations of a portable pH meter for use with water sampling are within ±0.2 pH units.
- 1.2 pH buffer aliquots are used only once.
- 1.3 Electrodes are maintained according to the manufacturer’s recommendations.
ApD-14
QC 4.1.4 Commercial buffer solution containers are dated upon receipt and when opened.
Solutions are discarded before the expiration date.
4.2 Light Microscope
- 2.1 The microscope is equipped with lenses to provide about 40X to 100X total magnification.
- 2.2 Optical clarity is sufficient to accurately count cells in a hemocytometer.
4.3 Inverted Light Microscope
- 3.1 The microscope is equipped with lenses to provide about 40X to 100X total magnification.
- 3.2 Optical clarity is sufficient to accurately demonstrate CPE.
- 4 Microbiological hood (if separate work areas are not available)
- 4.1 Hood is at least a class II biological safety cabinet.
QC 4.4.2 Hood is certified to be in proper operating condition on at least an annual basis.
4.5 Temperature Monitoring
- 5.1 Glass/mercury, dial thermometers or continuous recording devices are used to monitor equipment. Units are graduated in 0.5 C increments or less. Mercury columns in glass thermometers are not separated.
QC 4.5.2 The calibration at the temperature used of each glass/mercury thermometer is checked annually against a reference National Institute of Standards and Technology (formerly National Bureau of Standards) (NBS) thermometer or one that meets the requirements of NIST Monograph SP 250-23. The calibration of each in-use dial ther- mometer is checked quarterly.
QC 4.5.3 Correction data are available for all reference thermometers used for calibration.
QC 4.5.4 Continuous recording devices are recalibrated annually using the reference thermometer described in QC 4.5.2.
4.6 Incubator
- 6.1 The incubator maintains an internal temperature of 36.5 ± 1 C.
ApD-15
- 6.2 A temperature monitoring device is placed on a shelf near area of use. The bulb or probe of the temperature monitoring device is in liquid.
QC 4.6.3 The temperature is recorded at least once per day for each workday in use.
4.7 Refrigerator
- 7.1 The refrigerator maintains a temperature of 1 to 5 C.
- 7.2 A calibrated temperature monitoring device is placed on a shelf near the area of use. The thermometer bulb or probe is immersed in liquid.
QC 4.7.3 The temperature is recorded at least once per day for each workday in use.
4.8 Freezer, -20 C
- 8.1 The freezer maintains a temperature of -20 ± 5 C. The freezer may be a compartment associated with 4.6.
QC |
4.8.2
use.
4.8.3 |
A calibrated temperature monitoring device is placed on a shelf near the area of
The temperature is recorded at least once per day for each workday in use. |
4.9 Freezer, -70 C |
|
4.9.1 |
The freezer maintains a temperature of -70 ± 3 C or lower. |
|
4.9.2
use. |
A calibrated temperature monitoring device is placed on a shelf near the area of |
QC |
4.9.3 |
The temperature is recorded continuously during periods of use or at least once |
per day for each workday in use.
4.10 Refrigerated Centrifuge
- 10.1 The centrifuge can be operated at a centrifugal force of at least 4,000 ×g.
- 10.2 Centrifuge maintains an internal temperature of 4 C during run.
- 10.3 A rotor is available which is capable of 4,000 ×g while holding centrifuge bottles of 100 – 1000 ml.
ApD-16
QC 4.10.4 A log recording rotor serial number, run speed, time of centrifugation, tempera- ture of operation and operator is kept for each centrifuge run.
4.11 Balance
QC 4.11.1 The balance is calibrated monthly using Class S or S-1 reference weights (minimum of three traceable weights which bracket laboratory weighing needs) or weights traceable to Class S or S-1 weights.
QC 4.11.2 Correction data are available for the S or S-1 calibration weights.
4.11.3 A service contract or internal maintenance protocol is established and records are maintained.
4.12 Autoclave
- 12.1 The autoclave has a temperature gauge with a sensor on the exhaust, a pressure gauge and an operational safety valve.
- 12.2 Autoclave depressurizes slowly to ensure that media do not boil over.
- 12.3 The autoclave’s automatic timing mechanism is adequate. The autoclave maintains sterilization temperature during the sterilizing cycle and completes an entire liquid cycle within 45 min when a 12-15 min sterilization period is used.
- 12.4 A service contract or internal maintenance protocol is established and records are maintained.
- 12.5 A maximum temperature-registering thermometer or heat-sensitive tape is used with each autoclave cycle.
QC 4.12.6 Spore strips or ampules are used on a monthly basis.
QC 4.12.7 The date, contents, sterilization time and temperature is recorded for each cycle.
- 13 Hot Air Oven (If used for sterilizing dry glassware.)
- 13.1 The oven maintains a stable sterilization temperature of 170 – 180 C for at least two h.
- 13.2 A temperature monitoring device is used with the bulb or probe placed in sand during use. The monitoring device is graduated in no more than 10 C increments.
ApD-17
QC 4.13.3 The date, contents, sterilization time and temperature is recorded for each cycle.
4.14 Pump
A self-priming pump is required for preparation of QC samples. It is recommended that the pump be capable of pumping at a rate of 3 gal/min at 30 PSI.
4.15 Polypropylene Container
The container holds at least 40 L. The contents can be mixed without spilling or splashing.
4.16 Positive Pressure Source
An air or nitrogen source and pressure vessel or a peristaltic type pump is used for filter elution.
4.17 Magnetic Stirrer
The magnetic stirrer is capable of maintaining a vortex during organic flocculation and pH adjustments.
4.18 Source for Reagent Grade Water
- 18.1 Distillation and/or deionization units are maintained according to the manufac- turer’s instructions or water is purchased commercially.
- 18.2 Reagent grade water is used to prepare all media and reagents.
QC 4.18.3 The conductivity of the reagent grade water is tested with each use. The conductivity is >0.5 megohms-cm at 25 C.
5. General Laboratory Practices
5.1 Analytical Media
- 1.1.1 Commercial media and chemicals are dated upon receipt and when first opened. Only analytical reagent or ACS grade chemicals are used for the prepara- tion of media.
- 1.1.2 Use of commercial dehydrated or liquid media for propagation of tissue culture cells are recommended due to concern about quality control. Dehydrated media are prepared and stored as recommended by the manufacturers.
ApD-18
- 1.1.3 Commercial media and chemicals are discarded by manufacturers’ expiration dates. Laboratory prepared media are discarded by the expiration dates indicated in the Virus Monitoring Protocol.
- 1.1.4 Each lot of medium is checked for sterility before use as described in the Virus Monitoring Protocol.
QC 5.1.1.5 The lot numbers of commercial media and chemicals are recorded. The date of preparation, type of medium, lot number, sterilization procedure, pH and technician’s initials are recorded for media prepared in the laboratory.
5.1.2 Thiosulfate (2%)
- 1.2.1 A stock solution of 2% thiosulfate is prepared by dissolving 100 g of Na2S2O3 in a total of 5000 ml of reagent grade water. The solution is autoclaved for 30 min at 121 C.
- 1.2.2 2% thiosulfate is stored at or below room temperature for up to six months.
5.1.3 Hydrochloric acid (HCl)
- 1.3.1 Solutions of 0.1, 1 and 5 M HCl are prepared by mixing 50, 100 or 50 ml of concentrated HCl with 4950, 900 or 50 ml of reagent grade water, respectively. Solutions of HCl are self-sterilizing and should be prepared at least 24 h prior to use.
- 1.3.2 Solutions of HCl are stored at or below room temperature for up to six months.
5.1.4 Sodium Hydroxide (NaOH)
- 1.4.1 Solutions of 1 M and 5 M NaOH are prepared by dissolving 4 or 20 g of NaOH in a final volume of 100 ml of reagent grade water, respectively. Solutions of NaOH are self-sterilizing and should be prepared at least 24 h prior to use.
- 1.4.2 Solutions of NaOH are stored in polypropylene containers at room temperature for up to three months.
5.1.5 Beef Extract, 1.5%
- 1.5.1 Buffered 1.5% beef extract is prepared by dissolving 30 g of beef extract V powder and 7.5 g of glycine (final glycine concentration = 0.05 M) in 1.9 L of reagent grade water. The pH is adjusted to 9.5 with 1 or 5 M NaOH and the final
ApD-19
volume is brought to 2 L with reagent grade water. The solution is autoclaved at 121 C for 15 min.
- 1.5.2 Solutions of 1.5% beef extract are stored for one week at 4 C or for up to 18 months at -20 C.
5.1.6 Sodium Phosphate, 0.15 M
- 1.6.1 A solution of 0.15 M sodium phosphate is prepared by dissolving 40.2 g
of sodium phosphate (Na2HPO4 7H2O) in a final volume of 1000 ml of reagent
grade water. The pH is checked to ensure that it is between 9.0 – 9.5 and adjusted
with 1 M NaOH, if necessary. The solution is autoclaved at 121 C for 15 min.
- 1.6.2 Solutions of 0.15 M sodium phosphate are stored at or below room temperature for up to six months.
5.1.7 Washing Solution
- 1.7.1 Washing solution is prepared by dissolving 8.5 g of NaCl in a final volume of 980 ml of reagent grade water. The solution is autoclaved at 121 C for 15 min and cooled to room temperature. 20 ml of bovine serum is added and the solution is mixed thoroughly.
- 1.7.2 The wash solution is stored at 4 C for up to three months or at -20 C for up to 18 months.
5.1.8 Chlorine, 0.1%
- 1.8.1 A solution of 0.1% chlorine (HOCl) is prepared by adding 19 ml of household bleach to 900 ml of reagent grade water, adjusting the pH of the solution to 6-7 with 1 M HCl and bringing the final volume to 1 L with reagent grade water. Solutions of 0.1% chlorine are self-sterilizing.
- 1.8.2 Solutions of 0.1% chlorine are stored at or below room temperature for up to one month.
5.1.9 Iodine, 0.5%
- 1.9.1 A solution of 0.5% iodine is prepared by dissolving 5 g I2in 1000 ml of 70% ethanol. Solutions of 0.5% iodine are self-sterilizing.
- 1.9.2 Solutions of 0.5% iodine are stored at room temperature for up to six months.
ApD-20
5.2 Sterilization and Disinfection
- 2.1 Autoclavable glassware, plasticware and equipment are sterilized by auto- claving at 121 C for 1 h or, if appropriate, by dry heat at 170 C for at least one h.
- 2.2 Non-autoclavable supplies are disinfected with 0.1% chlorine (pH 6-7) for 30 min or in a gas sterilizer according to the manufacturer’s instructions.
- 2.3 Contaminated materials are sterilized by autoclaving at 121 C for at least 1 h.
- 2.4 Adequate glassware washing facilities are available for washing re-usable glassware.
- 2.5 All surfaces are disinfected with 0.5% iodine or 0.1% chlorine, pH 6-7 before and after each use and after any spill or other contamination.
6. Analytical Methodology
6.1 General
Only the analytical methodology specified in the July, 1995, draft of the Virus Monitoring Protocol for the Information Collection Rule is used for lab and analyst approval.
6.2 QC Samples
QC Each analyst and technician must prepare and process a negative QC sample during the site visit (technicians will only be required to perform steps 6.3 to 6.4). A negative QC sample is prepared by pumping 40 L of reagent grade water placed in a sterile polypro- pylene container through a sterile standard sampling apparatus.
6.3 Filter Elution
- 3.1 Residual water is blown out from the cartridge housing.
- 3.2 Virus is eluted from the 1MDS filter by slowly passing 1000 ml of 1.5% beef extract (pH 9.5) through the filter twice. The flow of beef extract is interrupted for 1 min during each pass to enhance elution.
- 3.3 An air filter is used with a positive pressure lab air source.
ApD-21
6.4 Organic Flocculation
QC 6.4.1 The pH meter is standardized at pH 4 and 7.
- 4.2 The pH electrode is disinfected before and after use.
- 4.3 The pH of the eluate is adjusted slowly to 3.5 ± 0.1 with 1 M HCl with stirring at a speed sufficient to develop a vortex.
- 4.4 The eluate is stirred for 30 min after pH adjustment.
- 4.5 The pH adjusted eluate is centrifuged at 2,500 ×g for 15 min at 4 C.
- 4.6 The supernatant is properly discarded after the centrifugation run.
- 4.7 The precipitate is dissolved in 30 ml of 0.15 M sodium phosphate.
QC 6.4.8 The pH meter is standardized at pH 7 and 10.
- 4.9 The pH electrode is disinfected before and after use.
- 4.10 The pH of the dissolved precipitate is readjusted to 9.0 – 9.5, if necessary.
- 4.11 The dissolved precipitate is centrifuged at 4,000 – 10,000 ×g for 10 min at 4 C.
- 4.12 The supernatant is removed and saved after the centrifugation run. The pellet is properly discarded.
- 4.13 The pH of the supernatant is adjusted to 7.0 – 7.5 with 1 M HCl.
- 4.14 The supernatant is treated to remove or reduce microbial contamination. Sterilizing filters are pretreated before use with beef extract.
- 4.15 The final volume is recorded after treatment.
- 4.16 The treated supernatant is divided into subsamples.
6.5 Total Culturable Virus Assay
QC 6.5.1 Passage 117 to 250 BGM cell cultures obtained from the U.S. EPA are being cultured for ICR virus assays.
ApD-22
- 5.2 Cultures are used between three and six days after the most recent passage or the laboratory has demonstrated that the culture time used is as sensitive as cultures at three to six days. Cultures are washed prior to inoculation with serum-free medium.
- 5.3 At least ten replicate cultures per subsample or subsample dilution are inoculated with an inoculation volume equal to 1/20th the assay sample volume.
6.4.4 The inoculation volume does not exceed 0.04 ml/cm2.
- 5.5 Virus is allowed to adsorb onto cells for 80 – 120 min at room temperature or at
36.5 ± 1 C.
- 5.6 Liquid maintenance medium is added and cultures are incubated at 36.5 ± 1 C.
- 5.7 A 2nd passage is performed using 10% of the medium from the 1st passage. Samples that were positive in the 1st passage are filtered before doing the 2nd passage.
- 5.8 The analyst demonstrates the ability to perform MPN calculations.
- 5.9 A positive and negative control is run with each sample.
7. Quality Assurance
The laboratory prepares and follows a written QA plan which is available for inspection during the site visit.
ApD-23